(302) 834-2100 (302) 834-4021 (Fax)
Thermal Expansion (CTE). During thermal cycling, the PCB and the aluminum expand and contract at different rates and different amounts. The CTE mismatch produces stress on the PCB driven by the aluminum sink, leading to possible PCB damage. The TIM, however, has a much lower shear modulus than the PCB or the aluminum. The compliance of the adhesive permits the decoupling of thermal expansion and contraction. 3) Dissipating thermal energy -- Conductive fillers in the TIM provide a heat transfer path to the aluminum heat sink. 4) Insulating electrically -- The TIM must provide dielectric breakdown protection and leakage current protection in the electronic application. The TIM can be made electrically conductive if a ground plane from the PCB to the Heat Sink is required.
II. Mechanism of thermal-mechanical decoupling
The shear modulus of the TIM is the most important aspect of thermal-mechanical decoupling. The thermal expansion and contraction of the PCB and the heat sink is shown in Figure 1. During a system’s life cycle, the respective temperatures of the PCB and the heat sink will increase and decrease. In this thermal cycle, the PCB and the heat sink both deform but at different rates due to their various CTE’s. Therefore, because the moduli of the PCB and the heat sink are much higher than that of the TIM between them, the thermal expansion and/or contraction amounts of the PCB and the heat sink are not dependent on the TIM, but, rather, solely on their respective CTE and
temperature differences. However, the induced stress of the PCB and the heat sink do depend on the modulus of the decoupling material. At the same deformation amount, a high shear modulus decoupling material such as an epoxy TIM induces more stress than does a low shear modulus TIM such as Arlon Thermabond® adhesive. If the stress is too high, it can deform and eventually damage the PCB (See Figure 2 below).
The mechanical properties of the TIM including shear modulus are determined by the structure of the material. The structure includes the chemical make up of the matrix, molecular weight, crosslink density, filler -- reinforcing and extending, and the interaction between the matrix and filler systems.
T↓ T↑



Figure 1: Thermal Expansion or Contraction of a PCB & Heat Sink during Thermal Cycling

Figure 2: The Deformation of a PCB Due to
Stress
F; VRIP = 1Vrms TM TS Thermal Muting Thermal ...decoupling Input DC decoupling Ripple rejection ...MECHANICAL DATA Multiwatt15 V 10/11 元器件交易网...
N.C. INR D99AU1016 THERMAL DATA Symbol Rth j-...decoupling Mute time constant Output DC decoupling ...MECHANICAL DATA Multiwatt15 (Vertical) 0016036 J ...
( 1. Department of Mechanical and Electrical Engineering,Luoyang Institute of...( SVMIPC ) was proposed,which indirectly achieved decoupling control between ...
enough to handle thermal loads and facing wear. ...The mechanical subsystem is located inside the ... excellent vibration decoupling thanks to adapted ...
In this paper, the coupling between two inputs is analyzed, with the imbalance of drive wheel and mechanical errors under consideration. A decoupling ...
F; VRIP = 1Vrms TM TS Thermal Muting Thermal ...decoupling Input DC decoupling Ripple rejection ...MECHANICAL DATA Multiwatt15 V 10/11 TDA7496 ...
(1) Frequency Stability Input DC Decoupling Larger...BUILD-IN PROTECTION SYSTEMS THERMAL SHUT-DOWN The...12 TDA2009A MULTIWATT11 PACKAGE MECHANICAL DATA DIM...
SW4 for mechanical request CON9 pin27 and pin30...Thermal Sensor NB Thermal Sensor P3 01 Battery ...DECOUPLING 17--SB600-STRAPS 18--RTS5158 & 3in1...
4. FC300 mechanical and Electrical installation_电子/电路_工程科技_专业资料...Decoupling plate for power cables Confidential / Property of 27 February, ...
Thermal/Mechanical Team CPU FET FET Vcc core decoupling Measure V Measure V...Pre-Test Preparation --Apply new thermal interface material (TIM) to the ...
热门文档