(302) 834-2100 (302) 834-4021 (Fax)
III. The effect of crosslink density
The polymer chains of silicone rubber are entangled, but they can be steadily disentangled under stress, leading to a viscous flow. The deformation can be partially recovered and the strength is low. Cross-linking or vulcanization is the process in which the polymer chains are linked together chemically by short chemical bonds to form a network, therefore transforming the material from a viscous material to an elastic solid. The cross-linking points restrict the disentanglement and deformation can be recovered and strength is high.
IV. The effect of the molecular weight of silicone rubber 3
The length of the polymer chain increases with molecular weight. Physical entanglement increases with the length of the polymer chain. The strength and shear modulus increase with the entanglement of the polymer chain. Therefore, the strength and shear modulus of cured silicone rubber increase as the molecular weight increases.
V. The effect of the reinforcing filler system
For the majority of applications, silicone rubber is too weak to use without reinforcing filler. Almost from the debut of the silicone industry, fumed silica and precipitated silica have been used as reinforcing fillers in silicone. Fumed silica has different properties and manufacturing processes than precipitated silica, and is more often utilized because of its high purity and low silanol-group density. The primary particles of fumed silica are extremely small spheres of only a few nanometers. Dispersion of fumed silica in the siloxane matrix is important for technical applications, particularly when good mechanical properties are required, due to filler networking. Good dispersion leads to improved reinforcement and subsequently excellent silicone physical properties.
A. Filler content
The mechanical properties of silicone rubber are also greatly dependent on the reinforcing filler content (see Figure 4 below). The shear modulus and hardness

Figure 3: The Dependence of Mechanical
Properties on Crosslink Density1
The mechanical properties of silicone rubber are greatly dependent on crosslink density, as is shown schematically in Figure 3. The shear modulus and hardness increase monotonically as the crosslink density increases; the material becomes more elastic or less hysteretic and the tensile strength passes through a maximum1.
F; VRIP = 1Vrms TM TS Thermal Muting Thermal ...decoupling Input DC decoupling Ripple rejection ...MECHANICAL DATA Multiwatt15 V 10/11 元器件交易网...
N.C. INR D99AU1016 THERMAL DATA Symbol Rth j-...decoupling Mute time constant Output DC decoupling ...MECHANICAL DATA Multiwatt15 (Vertical) 0016036 J ...
( 1. Department of Mechanical and Electrical Engineering,Luoyang Institute of...( SVMIPC ) was proposed,which indirectly achieved decoupling control between ...
enough to handle thermal loads and facing wear. ...The mechanical subsystem is located inside the ... excellent vibration decoupling thanks to adapted ...
In this paper, the coupling between two inputs is analyzed, with the imbalance of drive wheel and mechanical errors under consideration. A decoupling ...
F; VRIP = 1Vrms TM TS Thermal Muting Thermal ...decoupling Input DC decoupling Ripple rejection ...MECHANICAL DATA Multiwatt15 V 10/11 TDA7496 ...
(1) Frequency Stability Input DC Decoupling Larger...BUILD-IN PROTECTION SYSTEMS THERMAL SHUT-DOWN The...12 TDA2009A MULTIWATT11 PACKAGE MECHANICAL DATA DIM...
SW4 for mechanical request CON9 pin27 and pin30...Thermal Sensor NB Thermal Sensor P3 01 Battery ...DECOUPLING 17--SB600-STRAPS 18--RTS5158 & 3in1...
4. FC300 mechanical and Electrical installation_电子/电路_工程科技_专业资料...Decoupling plate for power cables Confidential / Property of 27 February, ...
Thermal/Mechanical Team CPU FET FET Vcc core decoupling Measure V Measure V...Pre-Test Preparation --Apply new thermal interface material (TIM) to the ...
热门文档