(302) 834-2100 (302) 834-4021 (Fax)
Thermal-Mechanical Decoupling by a Thermal Interface Material
Haibing Zhang, Ph.D.
Research and Development Chemist
Andy Cloud
Product Development Manager
Abstract
Thermal-mechanical decoupling by a silicone thermal interface material (TIM) is one of the most important properties in electronic applications involving a printed circuit board (PCB). Thermal-mechanical decoupling requires that the thermal interface material have low shear modulus and high elongation, while maintaining the integrity of other properties such as shear strength and thermal conductivity. The shear modulus and elongation of a thermal interface material depend on the structure of the material, which dictates the mechanical and thermal properties. The effect of crosslink density, molecular weight, the reinforcing filler system, the extending filler system, and the Payne effect on shear modulus and other mechanical properties are investigated in detail below. An analysis of the thermal-mechanical decoupling mechanism is included, as well as an introduction to viable approaches to lower the shear modulus of a silicone Thermal Interface Material.
III. The effect of crosslink density IV. The effect of molecular weight V. The effect of the reinforcing filler
system
A. Filler content
B. Filler surface activity C. Payne effect
VI. The effect of the extending filler
system
A. Filler content
B. Filler surface activity C. Payne effect
VII. Approaches to low shear modulus VIII. Summary IX. References
I. Introduction
Thermal interface materials (TIM’s), such as Arlon’s Thermabond® silicone adhesive, are used for bonding a printed circuit board (PCB) to a heat sink (usually aluminum), which dissipates heat away from the PCB. Silicone is primarily chosen as the adhesive polymer matrix because of its excellent thermal stability, low shear modulus, and good elasticity. The silicone TIM provides the following functions: 1) Bonding -- Bonding is particularly critical in vibration environments, such as automotive and aerospace. 2) Thermal-mechanical decoupling -- The PCB and aluminum heat sink have different Coefficients of
Contents
I. Introduction
II. The mechanism of thermal-mechanical decoupling
F; VRIP = 1Vrms TM TS Thermal Muting Thermal ...decoupling Input DC decoupling Ripple rejection ...MECHANICAL DATA Multiwatt15 V 10/11 元器件交易网...
N.C. INR D99AU1016 THERMAL DATA Symbol Rth j-...decoupling Mute time constant Output DC decoupling ...MECHANICAL DATA Multiwatt15 (Vertical) 0016036 J ...
( 1. Department of Mechanical and Electrical Engineering,Luoyang Institute of...( SVMIPC ) was proposed,which indirectly achieved decoupling control between ...
enough to handle thermal loads and facing wear. ...The mechanical subsystem is located inside the ... excellent vibration decoupling thanks to adapted ...
In this paper, the coupling between two inputs is analyzed, with the imbalance of drive wheel and mechanical errors under consideration. A decoupling ...
F; VRIP = 1Vrms TM TS Thermal Muting Thermal ...decoupling Input DC decoupling Ripple rejection ...MECHANICAL DATA Multiwatt15 V 10/11 TDA7496 ...
(1) Frequency Stability Input DC Decoupling Larger...BUILD-IN PROTECTION SYSTEMS THERMAL SHUT-DOWN The...12 TDA2009A MULTIWATT11 PACKAGE MECHANICAL DATA DIM...
SW4 for mechanical request CON9 pin27 and pin30...Thermal Sensor NB Thermal Sensor P3 01 Battery ...DECOUPLING 17--SB600-STRAPS 18--RTS5158 & 3in1...
4. FC300 mechanical and Electrical installation_电子/电路_工程科技_专业资料...Decoupling plate for power cables Confidential / Property of 27 February, ...
Thermal/Mechanical Team CPU FET FET Vcc core decoupling Measure V Measure V...Pre-Test Preparation --Apply new thermal interface material (TIM) to the ...
热门文档