Scaling Quad-Flat No-Leads Package Performance to E-band Frequencies
Sean S. Cahill, Eric A. Sanjuan
BridgeWave Communications, Inc.
Santa Clara, CA. 95054
;
Abstract— mm-Wave applications such as 60GHz WiGig, 77GHz Car Radar and 71-86GHz point-to-point communications have assumed center stage in recent years. While die technologies and circuit design capabilities have progressed significantly, little progress has been achieved in respective packaging solutions.
This paper describes a low-cost plastic MicroCoax enabled Quad-flat no-leads (QFN) based package capable of addressing increasing frequency needs. Presented package has excellent isolation between input-output signals, bias pins and controls as well as low insertion and return loss, which increases package bandwidth. The superior performance achieved with this package effectively maintains bare die performance at mm-wave frequencies. Furthermore, it simplifies mm-Wave chip design and integration with the printed circuit board (PCB), eliminating package-PCB 3D electro-magnetic interactions and thermal dissipation complications. The package leverages controlled impedance and well-isolated MicroCoax transmission lines, replacing traditional QFN wire bonds. QFN transitions to MicroCoax transmission lines are optimized for low mm-Wave discontinuities. Package performance results up to 65 GHz will be presented and scaling steps to enhance package frequency to 90GHz and beyond will be discussed. Testing QFN packages at mm-Wave frequencies poses a challenge and related test strategies will be reviewed. Since this package structure is broadband, it allows a variety of mm-Wave die and high speed analog chipsets to be assembled using the same process sequence and package configuration.
Dror Regev
Presto-Engineering Migdal Haemeq, Israel board (PCB), limiting the effective bandwidth of the packaged die. Bare die approaches compromise reliability of the devices because they are subjected to environmental stresses to a greater degree than packaged devices.
As a result, mmW designers of RFICs above 50 GHz have very limited choices if any, and many employ wafer level packaging (WLP) as the almost exclusive packaging alternative available. WLP’s high non-recurring engineering (NRE) costs may not be justified for low to medium volume production quantities. Adding thermal dissipation considerations and further complications at the PCB, and many will steer away from the WLP approach. Moreover, WLP flipped die, because they are still unshielded interconnects, form a new unified 3D electro-magnetic (EM) challenge along with the PCB that may affect RFIC performance or circuit stability that cannot be overlooked during RFIC circuit and layout design, further imposing increased efforts and constraints. Unfortunately, while investing in tedious 3D EM simulations seems inevitable in such cases, WLP distribution layer, transitions and proximity parasitics may still yield high levels of cross-talk between package bumps, especially at high mm-Wave frequencies. Such parasitics may also limit BW and can be tuned out only over narrow frequency bands.
The MicroCoax QFN (MCQFN) package described in this paper solves most of the above mentioned issues. Based on standard a QFN package, it offers cost structures similar to QFN and requires little die specific NRE, while serving many different die and applications. MCQFN has good thermal Keywords— QFN package, MicroCoax, mm-Wave Packaging
dissipation through the package ground, with straight-forward PCB means for heat sinking and minimal tradeoff for signal
I. INTRODUCTION
cross-talk. Since all die to package wire bonds are processed
Monolithic Microwave Integrated Circuit (MMIC) and into controlled impedance coax lines, both package BW and Radio Frequency Integrated Circuit (RFIC) devices are isolation between the formed transmission-lines increases operating at ever increasing speeds and over increasing significantly. Finally, the MCQFN package integration with frequency ranges. Plastic Quad-flat no-leads (QFN) packages PCB is far simpler than WLP. MCQFN allows for relatively reduce radio frequency parasitics by eliminating package leads simple 2D PCB design for fan out of different signals, bias and are known to be a low cost and common solution for lines and controls. frequencies below 10 GHz and in extreme cases, up to 28GHz. Yet, the self and mutual inductance/capacitance of bond wires II.MICROCOAX TRANSMISSION LINE FORMATION ANDlimit the use of these packages at higher mm-Wave (mmW)
PERFORMANCE TO 120 GHZ
frequencies. Ceramic packages with shorter wire bonds are
MicroCoax, an approach based on wire bonding, is similar known to perform well up to 40-50 GHz but at much higher
cost and may not be able to support higher frequencies. A in structure to a common coax cable. Leveraging energy simple wire bond inductance of 0.2nH at 50GHz, translates propagation contained within a controlled impedance cable, into an impedance of ~ j63 ohm in series with the common 50 MicroCoax allows signals to flow over a wide frequency ohm characteristic impedance of the die and printed circuit bandwidth. Fig.1 shows a cross-section of a MicroCoax,
978-1-4673-5756-2/13/$31.00 ©2013 IEEE. From the 2013 IEEE International Conference on Microwaves, Communications, Antennas and Electronic Systems (COMCAS 2013), Tel Aviv, Israel, 21-23 October 2013.
band frequencies (18) The output scattering parameters , , , and leads ,...4(a) and 5(a) clearly indicate the dual-band Fig. 7. Performance of ...
However, antenna performance is potentially degraded...The two resonance frequencies are obtained by ...(GHz) Flat 2.27 2.95 0.68 Lower band Bent...
(mA) 26 25 22 25 19 24.5 Package 6-pin ...Note f = 0.95 GHz Remark Typical performance. ...pass filters, suppressing low frequencies to DC. ...
Order Number Package Marking C3V Supplying Form ?...) 25.5 (2.2 GHz) Remark Typical performance....pass filters, suppressing low frequencies to DC. ...
and a lower cost performance solution to ...band frequencies for lower power applications such ...Package Wafer on Frame Die in Carrier Tape/Reel...
and a lower cost performance solution to ...band frequencies for lower power applications such ...Package Wafer on Frame Die in Carrier Tape/Reel...
Order Number Package Marking 6U Supplying Form ? ... is f = 0.95 GHz Remark Typical performance. ...pass filters, suppressing low frequencies to DC. ...
Intel Mac (dual-core): – good performance in preliminary timings – port...frequencies at GGA level (IV) Good parallel scaling up to 64 CPU’s ...
Leads to wider coverage and optimum performance ...Frequencies scanned Background scan with client ...package Adapter Input: 100-240V, 50/60Hz, 0....
Optimal uniform scaling factors calculated for the ...frequencies, 20 fundamental vibrations can be ...A general better performance of B3LYP and BLYP ...
热门文档