
A Broadband Quarter-wavelength Impedance Transformer Using
Vertically Installed Planar Coupler
Wei Jia Lu , Kian Sen Ang , Koen Mouthaan
1 2 1
1
Department of Electrical and Computer Engineering, National University of Singapore, 4 Engineering
Drive 3, Singapore 117576
2
DSO National Laboratories, 20 Science Park Drive, Singapore 118230
Abstract – A broadband quarter-wavelength impedance
transformer using a vertically installed planar (VIP) coupler is presented. A wide range of impedance transformation ratios and bandwidths can be achieved using this design. A 50 to 100 impedance transformer covering 0.7 GHz to 2 GHz is designed and implemented using the VIP. The measured results agree well with the simulation results. The design curves generated are useful for the design of this type of impedance transformer.
Index Terms -- Impedance transformer, vertically installed planar (VIP) coupler, passive circuit
I. INTRODUCTION
Impedance transformers are basic RF and microwave
components. Their application is found in impedance matching, power splitting and power combining circuits. There are many types of impedance transformers, such as conventional quarter-wavelength transformers, coupled-line transformers, multi-section transformers, tapered transformers and balun transformers [1]-[3].
The conventional quarter-wavelength transformers are the most commonly used transformers. They are easy to implement but have a narrow bandwidth. Wider bandwidths can be achieved using multi-section transformers [1] or coupled-line transformers [2], [3]. However, the physical size of these transformers poses a major constraint in highly compact microwave circuits [3]. A compact broadband impedance transformer was proposed in [4]. It employs a tightly coupled transmission line section and a high impedance transmission line loop. A compact size impedance transformer from 0.6 to 1.6 GHz was implemented. This transformer uses edge-coupled transmission lines in stripline. The bandwidth is limited by the realizable narrow gap between the two coupled lines, which is about 30 μm. This imposes a big challenge during fabrication.
An alternative way to achieve tight coupling is to use Vertically Installed Planar (VIP) coupled lines as first proposed by Y. Konishi to achieve tight coupling in his directional coupler designs [5], [6]. VIP enables realization of high couplings without tight spacing limitations. In this paper, the VIP coupler is adopted to implement the broadband impedance transformer in [4], so as to relieve the challenges faced when edge coupling is used.
Fig. 1 (a) Schematic diagram of the proposed quarter-
wavelength impedance transformer in [4]. (b) Quarter-wavelength impedance transformer using VIP coupler.
II. THE STRUCTRE OF THE IMPEDANCE
TRANSFORMER
Fig. 1(a) shows the impedance transformer proposed in [4]. The parameters affecting the impedance transformation ratio and the bandwidth are transmission line impedance Z 0, and the even and odd mode impedances Z0e and Z0o of the coupled lines. Fig. 1(b) shows the proposed implementation of the broadband impedance transformation circuit. It consists of a horizontal printed circuit board (PCB) and a vertically installed PCB.
The conventional quarter-wavelength impedance transformer is easy to implement ...A compact broadband impedance transformer with three reflection zeros was ...
. Case 1: a quarter-wavelength transformer of impedance of 31.6 ? , ...-10 dB 30 to 70 degrees Qingyuan Wang, “Broadband microstrip circuits, ...
Unit 4:Resonant Modes, Bilinear Transformation between Impedance and Reflection... ) 11 Quarter-wavelength Transformer lg 4 Z0 Zg Z0 d1 ZL d1 = l ...
A broadband series power divider using zero-degree metamaterial phase-...quarter-wavelength transformers were added to provide a broadband impedance ...
4 Broadband selected to give a maximally flat response.6 These transitions ...Each transformer contains three one-quarter-wavelength steps with impedance ...
5-1 CHAPTER 5 Impedance Matching and Smith Chart...(such as broadband design) - adjustability - ...Chuang EE NCKU 5-23 ??Quarter-Wave Transformer ...
Resistive feedback and transformer matching network are proposed in this PA design to enhance the broadband frequency response. The broadband load impedance ...
(narrow band techniques) or for a given frequency spectrum (broadband ...The quarter-wavelength transformer provides narrow-band impedance matching. The...
Harmonic Suppression in Broadband Microstrip Patch ...quarter-wavelength transformer feeding as well as ...However, their large input impedance at the ...
Broadband circularly pol... 暂无评价 4页 2财富值 08_Fractal boundary ... and a quarter-wavelength impedance transformer is used to overcome the ...
热门文档