
Fig. 1. Wire bond-based microCoax
(1) The characteristic impedance of a coax line is given in Eq. (1), where L is the inductance per unit length, C is the capacitance per unit length, a is the diameter of the bond wire,
b is the outside diameter of the dielectric and εr is relative permittivity of the coaxial dielectric. A typical microCoax is about 70 microns in diameter. Since the desired propagation mode in a coax cable is the TEM mode, the coax maximum frequency will be considered as the minimum cutoff frequency
of the TE11 propagation mode. Equation (2) describes the maximum TEM propagation frequency in a coax cable:
(2)
where c is speed of light and μr is relative permeability of the coaxial dielectric. Wire bond MicroCoax dimensions and dielectric layer suggest frequency operation approaching roughly 1 THz.
References [1] and [2] detail the fairly simple process for turning a wire bond into a MicroCoax. Standard 0.6-0.7 mil wire bonds are coated uniformly with dielectric then selective etching for ground via openings follows and subsequent metal deposition forms the coax outer shield and ground connections. Fig. 2 shows the formation of MicroCoax Grounded Coplanar Waveguide (GCPW) test structures. Such 50 ohm MicroCoax test structures were tested in [1] for isolation up to 100GHz and showed a minimum of 35-40dB isolation between a pair longer than 2 mm MicroCoax wires (after neutralizing substrate coupling). Fig. 3 shows the insertion and return loss performances of such MicroCoax transmission lines. Superior

results achieved by MicroCoax with a fairly simple and cheap

Fig. 2. MicroCoax test structures left to right: Dielectric-coated wire bonds; after outer metal shield is in place. Note the circular via ground connections.
process sequence can be employed in mmW packaging when coupled with an open cavity QFN. This will be discussed in the next section.
Fig. 3. Performance of 2.2 mm long MicroCoax (Measurement Courtesy
Motorola Embedded Systems Lab)
III. MICROCOAX QFN: CHARACTERISTICS TO 65 GHZ
A standard JEDEC 95 QFN package of the open-cavity variety is shown in Fig. 4. It has several desirable attributes as mentioned earlier. Three adjacent QFN leads in a GSG
configuration can be considered as quasi- coplanar waveguide (CPW) and when soldered to a PCB interface as a quasi- grounded coplanar waveguide (GCPW) or Quasi-Rectangular Coax. Standard QFN package lead and pitch dimensions with a plastic material of dielectric constant value ranging from 3.5
– 4.0 can support a 50 ohm impedance transition to PCB [2]. MicroCoax port-to-port through lines constructed in QFN are
shown [2] and in Fig. 4. The package has the general outline of the standard 0.5mm pitch QFN and contains geometric enhancements internal to the package that improve the high freuency performance when used in combination with MicroCoax [2]

.

G G
G
G
Fig. 4. (left to right) 5 mm Standard Open Cavity QFN Package; MicroCoax
Enhanced QFN Package with enhanced ports; the same package with coaxial through-line; close-up of port/through-line structure
MCQFN packages were soldered to a Rogers substrate and reference lines added to enable tests up to 65GHz (Fig.5). Gated TDR measurement (excluded connector and MS line) was employed for characterizing Sloss employed for de-embedding S11 and through line insertion 21

for MCQFN.
Fig. 5.

MCQFN test board
band frequencies (18) The output scattering parameters , , , and leads ,...4(a) and 5(a) clearly indicate the dual-band Fig. 7. Performance of ...
However, antenna performance is potentially degraded...The two resonance frequencies are obtained by ...(GHz) Flat 2.27 2.95 0.68 Lower band Bent...
(mA) 26 25 22 25 19 24.5 Package 6-pin ...Note f = 0.95 GHz Remark Typical performance. ...pass filters, suppressing low frequencies to DC. ...
Order Number Package Marking C3V Supplying Form ?...) 25.5 (2.2 GHz) Remark Typical performance....pass filters, suppressing low frequencies to DC. ...
and a lower cost performance solution to ...band frequencies for lower power applications such ...Package Wafer on Frame Die in Carrier Tape/Reel...
and a lower cost performance solution to ...band frequencies for lower power applications such ...Package Wafer on Frame Die in Carrier Tape/Reel...
Order Number Package Marking 6U Supplying Form ? ... is f = 0.95 GHz Remark Typical performance. ...pass filters, suppressing low frequencies to DC. ...
Intel Mac (dual-core): – good performance in preliminary timings – port...frequencies at GGA level (IV) Good parallel scaling up to 64 CPU’s ...
Leads to wider coverage and optimum performance ...Frequencies scanned Background scan with client ...package Adapter Input: 100-240V, 50/60Hz, 0....
Optimal uniform scaling factors calculated for the ...frequencies, 20 fundamental vibrations can be ...A general better performance of B3LYP and BLYP ...
热门文档