sections should be considered in the analysis. Furthermore, a suggest that reducing conductor distance to ground will reduce distance to an ideal ground (in discontinuities such as Step 1) QFN Quasi-Rectangular Coax dispersion (may not be easy to of 350-400um accounts for approximately a quarter derive analytically). wavelength at 100GHz and can transform the distant ground to
an open circuit to ground rather than a short.
In Fig. 9, Step 1 represents a lumped parasitic effect resulting from abrupt transition from PCB GCPW to the signal
lead section (TL1- a QFN Quasi-Rectangular Coax). Step 1 also represent a major discontinuity is grounds from GCPW to 0.5mm pitch GSG in the QFN which may involve significant distributed effects on the ground path as well. Distributed effects that transform a distant ground to an open circuit may
be approximated by parallel LC network resonating at quarter
wavelength frequencies. Z01 and φ1 represent the QFN lead section impedance and electrical phase. Step 2 represents a lumped parasitic effect resulting from abrupt transition between the two QFN copper layers forming the lead frame. Top copper layer form another Quasi-Rectangular Coax section
TL2, where Zelectrical phase. Step 3 accounts for the lumped parasitic effect
02 and φ2 represent the section impedance and resulting from abrupt transition between the top layer of the lead frame section to MicroCoax section. One can observe Step
3 in Fig. 4 and assume it contributes a parallel LC branch parasitic (as described for Step 1) on ground path resulting from physical distance to leadframe ground through ground vias, as well as a shunt capacitance of the coax ground shield to
the top leadframe copper layer forming the center conductor.
Quasi-Rectangular Coax transmission lines are described analytically and graphically in [5] and compared with characteristic impedance of circular coaxial lines. From [5] one can observe that the characteristics impedance of a Quasi-Rectangular Coax is approximated by (6): (6)
This higher impedance result may be explained by the reduced capacitance per unit length such a transmission line cross section poses. Hence, a comparison to RG-196 “1 mm” coax cable may be valuable as it is capable performing up to 112GHz. An RG-196 has a center conductor diameter a of 0.305mm, an outer dielectric conductor diameter b of 0.864mm and PTFE dielectric constant εεr of 2.1. From (6) and since the QFN has Coax line with cross-sections dimensions as described in Fig. 8 r ~ 4, one can estimate that a Rectangular will have an impedance lower than 50 ohm. Careful analysis including EM simulations, however, must be performed to verify this and also ensure no higher propagation modes are enabled with frequency approaching 100GHz.
Eq. (2) states that fc, the maximum cut-off frequency, is
inversely proportional to the square root of εtransmission line cross-section dimensions. Since QFN Quasi-r and to Rectangular Coax sections have εr about twice as much as RG-196 and has no full circumference shield like a coax, it is safe to say that the cross section dimensions of these sections must be scaled down to reject higher modes and surface waves below 100GHz. Microstrip dispersion formulas in [6] and [7] We have neglected discussing Step 2 discontinuities that may be another significant source of matching imperfection.
All these abrupt steps may need reduction in size to decrease
discontinuity parasitics for higher frequencies, as is suggested in the next section. V. MICROCOAX QFN PERFORMANCE SCALING TO E-BAND FREQUENCIES Fig. 10 describes bottom views of typical 3x3 mm QFN packages with different lead pitches of 0.5mm and 0.4mm.
Scaling down critical dimensions to increase BW is the first promising measure one can take when QFN performance is considered. Lead dimensions affect Step 1 discontinuities
(Fig.9) from a PCB GCPW strip thinner than 20um into a lead of roughly 100um thick soldered on top. A Step 1 discontinuity
will be highly affected by the two ground lead distances to the signal lead, scaling down as 50 ohm GCPW ground planes get
closer to the QFN high frequency leads. In a similar way, one

can expect that Step 2 and Step 3 parasitics will reduce with down scaling of dimensions. TL1 in Fig. 9 models the QFN signal and two neighboring ground leads forming a
transmission line with the PCB. The length of this section is specified in JEDEC and cannot be optimized or reduced. Yet looking at Fig. 10, one can observe a length of 350um for the
lead. Even if tighter pitch QFNs (Amkor currently offers 0.3mm pitch QFNs) can reduce this length to ~300um, it will still account for roughly 0.2λ at 100GHz. TL1 must be treated and optimized to be a WB 50 ohm transmission line in
impedance and free of higher modes up to 100GHz. TL2
dimensions are not specified in JEDEC and hence its length may be physically shortened, however since it cannot be shorter than 100um, it must be designed as a WB 50 ohm section. Step 3 must be designed to shorten ground paths from
the MicroCoax shield to the lead frame top layer ground and to minimize shunt capacitance.
Fig. 10. 3x3mm QFN bottom views: 0.5mm (left); 0.4mm pitch (right)
Fig. 11 shows the impact (simulated) of moving from
0.5mm to 0.4 mm pitch for the MCQFN design and optimizing
for various discontinuities as previously discussed. Note that the bandwidth is extended to substantially improve potential E-band performance while largely maintaining the performance in the lower bands. Moving to even smaller form factors (e.g.,
band frequencies (18) The output scattering parameters , , , and leads ,...4(a) and 5(a) clearly indicate the dual-band Fig. 7. Performance of ...
However, antenna performance is potentially degraded...The two resonance frequencies are obtained by ...(GHz) Flat 2.27 2.95 0.68 Lower band Bent...
(mA) 26 25 22 25 19 24.5 Package 6-pin ...Note f = 0.95 GHz Remark Typical performance. ...pass filters, suppressing low frequencies to DC. ...
Order Number Package Marking C3V Supplying Form ?...) 25.5 (2.2 GHz) Remark Typical performance....pass filters, suppressing low frequencies to DC. ...
and a lower cost performance solution to ...band frequencies for lower power applications such ...Package Wafer on Frame Die in Carrier Tape/Reel...
and a lower cost performance solution to ...band frequencies for lower power applications such ...Package Wafer on Frame Die in Carrier Tape/Reel...
Order Number Package Marking 6U Supplying Form ? ... is f = 0.95 GHz Remark Typical performance. ...pass filters, suppressing low frequencies to DC. ...
Intel Mac (dual-core): – good performance in preliminary timings – port...frequencies at GGA level (IV) Good parallel scaling up to 64 CPU’s ...
Leads to wider coverage and optimum performance ...Frequencies scanned Background scan with client ...package Adapter Input: 100-240V, 50/60Hz, 0....
Optimal uniform scaling factors calculated for the ...frequencies, 20 fundamental vibrations can be ...A general better performance of B3LYP and BLYP ...
热门文档