Fig. 6 shows MCQFN performance DC to 65 GHz. Results shown are for MCQFN with 4 mm MicroCoax “back to back” through line structure (as per Fig. 4) with excellent

IV. MICROCOAX QFN DISCONTINUITIES AND INTERFACE
TO PCB Fig. 8 details a physical cross-section and critical performance up to 65GHz.
Fig. 6. Fixture based test of MCQFN back-to-back MicroCoax through-line
Fig. 7 is a model of a structure shown in Fig. 5 where the MicroCoax 4 mm section is assumed as an ideal transmission line and the two sections of the QFN assumed identical. To evaluate the performance contribution of a single QFN section, the values measured at Fig.7 can be used. It can be shown that back to back S21T and S11T are given by (3) and (4):
(3)


(4)
Fig. 7. Model of the MCQFN test structure tested and S-parameter representation Hence the S-parameter performance of a single QFN port section is even better than the values shown in Fig.6, accordingly. Comparing these results with results presented of a 2mm MicroCoax from Fig.3, one can estimate the insertion loss of the MCQFN section with a short MicroCoax to the RFIC as lower than 0.5dB at 65GHz. This result is significant, since such a loss will be translated to added noise figure on receivers or reduction in transmitted power for transmitters and hence must be kept to a minimum. dimensions of an open-cavity QFN lead connected to a MicroCoax on one end and soldered to a PCB GCPW transmission line on the other [2]. While both MicroCoax and GCPW (or Microstrip) transmission lines can be designed with a characteristic impedance of 50 ohm and maximum cut-off frequency above 100GHz, several discontinuities exist that may impair operation above 50GHz. The transition between MicroCoax and mmW RFIC may be considered negligible, however other discontinuities, both lumped and distributed elements should be considered. Fig. 9 describes a suggested simplified equivalent network model for the package shown in Fig. 8. One can observe that this entire network is represented in Fig.7 as Sa,

the S-parameter form of the QFN section.

Fig. 8.

MCQFN 3D cross-section, side and top view of cavity metal details
Fig. 9. QFN package interface - simplified equivalent network model
L and C characteristic values from (1) may abruptly change when transitioning through transmission line discontinuity sections and cause signal reflections. References [3] and [4] explored lump network representations for CPW
discontinuities (similar for microstrip). Similar networks may
be used to describe the steps in Fig.9. Longer QFN sections
may have distributed discontinuity effects on the characteristic
impedance. Signal wavelength is inversely proportional to frequency of operation and is given in Eq (5):

(5) Hence, at 100GHz and for QFN εr of roughly ~ 4, the wavelength is 1.5mm. This implies that even 100um length
band frequencies (18) The output scattering parameters , , , and leads ,...4(a) and 5(a) clearly indicate the dual-band Fig. 7. Performance of ...
However, antenna performance is potentially degraded...The two resonance frequencies are obtained by ...(GHz) Flat 2.27 2.95 0.68 Lower band Bent...
(mA) 26 25 22 25 19 24.5 Package 6-pin ...Note f = 0.95 GHz Remark Typical performance. ...pass filters, suppressing low frequencies to DC. ...
Order Number Package Marking C3V Supplying Form ?...) 25.5 (2.2 GHz) Remark Typical performance....pass filters, suppressing low frequencies to DC. ...
and a lower cost performance solution to ...band frequencies for lower power applications such ...Package Wafer on Frame Die in Carrier Tape/Reel...
and a lower cost performance solution to ...band frequencies for lower power applications such ...Package Wafer on Frame Die in Carrier Tape/Reel...
Order Number Package Marking 6U Supplying Form ? ... is f = 0.95 GHz Remark Typical performance. ...pass filters, suppressing low frequencies to DC. ...
Intel Mac (dual-core): – good performance in preliminary timings – port...frequencies at GGA level (IV) Good parallel scaling up to 64 CPU’s ...
Leads to wider coverage and optimum performance ...Frequencies scanned Background scan with client ...package Adapter Input: 100-240V, 50/60Hz, 0....
Optimal uniform scaling factors calculated for the ...frequencies, 20 fundamental vibrations can be ...A general better performance of B3LYP and BLYP ...
热门文档