超高压电
Fig. 5 Depiction on can and be COP comparisons in this work are performed using the system considered P-h diagram of two possible cycles that
pressure when on COP predicting for two-phase impact of cooling. coolant low temperature COP path (vapor compression and high smaller expected condenser volumes
condensation) which is associated with pumped to high pressure in liquid phase. This approach is not viable condenser size) for heat rejection to ambient and extra coolant when required high surface area (and therefore larger capacity reservoir are not practical, or when a stable low condenser) for external heat sinking cannot be guaranteed. In (below saturation temperature of the coolant temperature in the the approach that results in a lower predicted COP the vapor leaving then compression condensed the microgap at high is compressed temperature to and a superheated vapor liquid comes with the benefit of smaller condenser size.
pumping, requires but the a considerably heat rejection greater pressure. at high work temperature input Vapor than case inlet and outlet pressure drop, to investigate the variation We use the thermodynamic model, augmented with worst-of COP at the optimum (maximum height k/H) mass flux/ microgap depicted for isentropic compression and constant pressure heat rejection in in the Fig. same 4. For coolant, the COP inlet determination, temperature combinations we assume the condenser. We find that the trend for predicted COP with respect to maximum system pressure is the opposite as that for kseen in Fig. 6. For example, the R134a refrigerant have been /H, with lower COPs predicted at higher system pressures, as identified maximum as k/H~500 W/ma better heat transfer performance 2K at ~75ocoolant (with COP~6 at these operating conditions. This trend is primarily a C), but features rather low result higher overall system pressures, which have to be recovered in of the larger pressure drops that were achievable at the greater close-loop operation associated with larger mass fluxes.power input to the of compressor, cooling cycle
as by well requiring as losses a REDUCED ORDER ANALYSIS WITH FRICTION
reached We assess the impact of friction on the implementation in the hydrodynamic of a thermodynamic reduced order analysis conclusions (1-D) two-phase through energy analysis. Friction will result in greater pressure drops model in combination with thermodynamic which could produce several deleterious effects, including
Fig. 6 vapor compression before condensing and accounting COP at the condition of maximum k/H, assuming
for manifolds, coolant acceleration due to liquid-to-vapor all pressure drop constituents (inlet/exit phase change and friction), as a function of maximum pressure 308.15 K
at inlet temperatures from 358.15 K to reduced power coefficient of performance and larger cooling system size due requirements, heat transfer which performance yield and both increased decreased pumping system to a need to reject more energy in the system condenser. Reduced Order Model
state, The thermodynamic separated reduced order flow model model is in a which one-dimensional, we assume steady-local system. Mass conservation is still expressed through Eq. equilibrium for each cross section of the while energy two first order ordinary differential (1), respectively:
and momentum conservation, i.e., equations Eqs. (6) and impose (7), dh
q
(6) dP G2d 1 dP
Calculation (7) f
the empiricism. last term of the in Eq. frictional (7), requires pressure the drop, incorporated into phase phase frictional Following pressure Kim drop et al., [1] we introduction estimate the of two-an Fanning (liquid) as the product of the single Appendix):
friction frictional factor, f,pressure and a two-phase drop, calculated multiplier, using (see the dP
2f [(1 xf
)G]2 2 (8) The laccompanied with initial conditions system of two first order differential equations is h(z 0) h(T Tin,x 0) (9) and P(z 0) P(T Tin,x 0)
(10)
www.elsevier.com/locate/ijhmt Investigation of the two-phase convective ...in COP for HFO-1234yf system at a same cooling capacity with HFC-134a....
CFD simulation of convective flow boiling of refrigerant in a vertical ... of the wall lubrication force is necessary for the adiabatic two-phase ?...
upon the merits of phase change to achieve the desired cooling performance....Two key merits of boiling in microchannels are (1) very large convective ...
Convective WeatherConvective Weather隐藏>> Convective...Stages of Air Mass Thunderstorms Cumulus Phase ? ...? Produces temporary cooling ? Slight potential ...
two-phase mixture level, which directly determines the cooling capability and...(2003) can be applied to convective and pool systems; in addition, ...
economic and effective methods in producing ultra-... is considered to satisfy the convective equation ...Hence for E / E0 1, the laminar two-phase ...
Cooling Electronics with Nanofluids Laminar Convective Nanofluids Nanofluids Nan...Horizontal Tube Using Two-Phase Mixture Model,” Applied Thermal Engineering,...
principle and its applications in enhancing single phase convective_工学_高等... it can be seen that there are two disadvantages for the existing ...
(2005)Forced convective heat transfer across a ...singlephase [1–4] and boiling (two-phase ow)...for electronic cooling heat sinks have been ...
热门文档