文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 自然科学 > 物理 > Two phase convective cooling for ultra-high power dissipation in microprocessors
侵权投诉

Two phase convective cooling for ultra-high power dissipation in microprocessors

超高压电

Two phase convective cooling for ultra-high power dissipation in microprocessors

Fig. 3 Ratio of thermal conductivity to microgap height (which serves as a proxy for heat transfer coefficient, as k/H),

a function of outlet pressure for a variety of coolants. With the exception of water and methanol, all maxima fall Several close were coolants to a line that that were depicts included the trend in the k/H~ Pout. these displayed unusual behavior. removed from the figure for clarity – analysis none of small gaps can be achieved in higher pressure systems because of the larger vapor densities at higher outlet pressures, which results in smaller accelerational pressure drops.

conditions The results which saturated in Fig. liquid 3 were at all a obtained temperature assuming as inlet course therefore of expansion and contraction at the microgap outlet and inlet, different for determined different the fluids. inlet Furthermore, pressure, of which 358.15 the impact is K, of respectively, is not considered. the increased trend of reduced achievable In order to further investigate microgap thickness due R245fa, R123, and R236fa) and identified for each coolant, at system pressure, we chose four coolants (R134a, to temperatures achievable from 298.15 K to 358.15 (1)-(3), with the coolant entering the microgap as a saturated k/H based on the thermodynamic model, i.e., Eqs. K the maximum liquid (was drops, augmented x=0) and leaving as saturated vapor (x=1). The model and (5) [8]

Pwith worst case inlet and outlet pressure in and Pout, respectively, incorporated via Eqs. (4) PG2in 38 1.64 (4) l

2 Pout

G

(5)

Because compared to the liquid density at the inlet, the pressure drop of the lower density of the v

vapor at the outlet as due to expansion at the outlet, predicted by Eq. (5), is always larger than the contraction inlet pressure drop predicted by Eq. (4), drop in the microgap predicted by Eq. (3). The results of the and it is very nearly 25% of the accelerational pressure thermodynamic case which inlet and outlet analysis augmented by inclusion of worst function displays the optimal pressure (max drops k/are H) depicted in Fig. 4, slightly subcooled liquid in the inlet manifold prior to entering of the maximum system pressure design (pressure point of as the a the microgap). When comparing results in Figs. 3 and 4 it is

important plotted scaling identified in the figure of against to keep outlet in mind pressure that the results in Fig. 3 were Fig. kto /H~ highlight Pthe important out, while the results in saturation pressure at the inlet temperature plus the worst case 4 are plotted against the maximum pressure: the pressure into the microgap. Thus Fig. 4 is conceived as a design aid, in drop due to constriction from an arbitrary manifold which performance at increased system pressure can be viewed in the the trend of improved predicted heat transfer context of controllable inlet pressure for a given coolant. For example, MPa, heat then if examination reliability concerns of limit system pressure to 1 which would be obtained by maintaining inlet temperature at transfer coefficients for Fig.4 R134a indicates than the predicted other coolants, higher 308.15 temperatures K. All would presumably require larger system condensers.

provide other a greater things margin being to equal, thermal lower limits, inlet but Fig. 4 height (Maximum ratio of thermal conductivity to microgap

four 358.15 coolants k/H) as a function of maximum pressure for a inlet temperature. The red symbols are from solution of K, with at each decreasing point taken inlet at temperatures 10 K intervals from of the are discussed in the next section. reduced order model, which includes friction, and lower The tradeoff discussed above in the context of Fig. 4, that wall temperatures at the expense of larger condensers, is not coolant temperatures can remove heat fluxes at lower the system only current level tradeoff concerns between that can heat be transfer considered performance and coefficient analysis. point cooling in discussion of performance Another important concern in is light the system of the of COP (COP). for systems A sometimes designed overlooked for chip assumptions about the remainder of the cooling cycle (e.g., [9] is that COP comparisons require consistency in and condensing Fig. 5). Figure 5 the approach that results in a much higher predicted COP, the the vapor leaving depicts the two microgap possible (evaporator). approaches In to vapor is condensed at low temperature and pressure and then

上一页第3页

你可能喜欢

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email