IC datasheet pdf-DS1876,pdf (SFP Controller with Dual LDD Interface)
SFP Controller with Dual LDD Interface
DS1876
DETECTION OF TXFOUT FAULT
TXFOUT
Figure 11a. TXFOUT Nonlatched Operation
DETECTION OF TXFOUT FAULT
TXD_ OR TXFOUT RESET
TXFOUT
Figure 11b. TXFOUT Latched Operation
Transmit Fault (TXFOUT) Output
START Condition: A START condition is generated TXFOUT can be triggered by all alarms, warnings, QTs, by the master to initiate a new data transfer with a TXD1, TXD2, TXF1, and TXF2 (see Figure 9). The six slave. Transitioning SDA from high to low while SCL ADC alarms and warnings are controlled by enable bits remains high generates a START condition. See (Table 01h/05h, Registers F8h and FCh). See Figures Figure 12 for applicable timing.
11a and 11b for nonlatched and latched operation for TXFOUT. The CNFGB register (Table 02h, Register 89h) STOP Condition: A STOP condition is generated controls the latching of the alarms.
by the master to end a data transfer with a slave. Transitioning SDA from low to high while SCL remains Die Identification
high generates a STOP condition. See Figure 12 for The DS1876 has an ID hardcoded in its memory. Two applicable timing.
registers (Table 02h, Registers 86h-87h) are assigned for this feature. Register 86h reads 76h to identify the Repeated START Condition: The master can use part as the DS1876; Register 87h reads the present a repeated START condition at the end of one data device version.
transfer to indicate that it will immediately initiate a new data transfer following the current one. Repeated 2C Communication
STARTs are commonly used during read operations to identify a specific memory address to begin a data I2C Definitions
transfer. A repeated START condition is issued identi-The following terminology is commonly used to describe cally to a normal START condition. See Figure 12 for I2C data transfers.
applicable timing.
Master Device: The master device controls the slave Bit Write: Transitions of SDA must occur during the devices on the bus. The master device generates SCL low state of SCL. The data on SDA must remain valid clock pulses and START and STOP conditions.and unchanged during the entire high pulse of SCL Slave Devices: Slave devices send and receive data plus the setup and hold time requirements (Figure 12). at the master’s request.
Data is shifted into the device during the rising edge of the SCL.
Bus Idle or Not Busy: Time between STOP and START conditions when both SDA and SCL are inac-Bit Read: At the end of a write operation, the master tive and in their logic-high states.
must release the SDA bus line for the proper amount of setup time (Figure 12) before the next rising edge

______________________________________________________________________________________ 19
IC datasheet pdf-DS1877,pdf,datasheet,SFP Controller for Dual Rx Interface_信息与通信_工程科技_专业资料。IC datasheet pdf-DS1877,pdf,datasheet,SFP ...
IC datasheet pdf-ONET8531T,pdf(11.3Gbps ...ONET8531T With Dual Cathode PIN Diode Copyright ?...Products DSP Clocks and Timers Interface Logic ...
元器件交易网www.cecb2b.com Datasheet 8 Gbps Bi...(Duplex LC) Dual-fiber, bi-directional Class 1...2-wire Serial Interface Data Line (MOD-DEF2) ...
? Customer’s MAC should be setup for SGMII interface with Auto-Negotiation... IC datasheet pdf-DS187... 65页 免费 AN4138C(20G四通道SFP有... 20页 ...
datasheet 11页 免费 XFP模块电路设计 6页 1下载...Assembled with low EMI emissions IC and fully ...Interface GBIC 1000Base-X to 1000Base-T SFP-...
IC datasheet pdf-DS1876,... 69页 免费 AlGaNGaN+HEMT的研制 60页 免费 ... Normally Off AlGaNGaN Low-Density Drain HEMT (LDD-HEMT) With Enhanced ...
The resistor range for the laser current settings is optimized to interface with the DS1858 SFP controller IC. The MAX3735/MAX3735A provide transmit-...
interface Duplex LC connector Built-in digital ...Datasheet Digital Diagnostics Functions MRV’s SFP-...Controller (DDTC) inside the transceiver, which ...
dual-loop LDD, allowing one PC board layout to...APPLICATIONS 1×/2×/4× Fibre Channel SFP/SFF...Control with a Single-Ended Laser Interface Rev....
Datasheet MAX3735 - 2.7Gbps, Low-Power SFP Laser Drivers - Maxim ... settings is optimized to interface with the DS1858 SFP controller IC. ...
热门文档