文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 信息与通信 > IC datasheet pdf-DS1876,pdf (SFP Controller with Dual LDD Interface)
侵权投诉

IC datasheet pdf-DS1876,pdf (SFP Controller with Dual LDD Interface)

IC datasheet pdf-DS1876,pdf (SFP Controller with Dual LDD Interface)

SFP Controller with Dual LDD InterfaceDS1876

IC datasheet pdf-DS1876,pdf (SFP Controller with Dual LDD Interface)

Figure 9. Logic Diagram 1

Register 89h). The open-drain RSELOUT output is software controlled and/or inverted through the STATUS register and CNFGA register (Table 02h, Register 88h). External pullup resistors must be provided on OUT1 and RSELOUT to realize high logic levels.

TXF1, TXF2, TXFOUT, TXD1, TXD2,

TXDOUT1, TXDOUT2

TXDOUT1 and TXDOUT2 are generated from a com-bination of TXF1, TXF2, TXD1, TXD2, and the internal signals FETG1 and FETG2 (Table 02h, Register 8Ah). A software control identical to TXD1 and TXD2 is also avail-able (TXDC1 and TXDC2, Lower Memory, Register 6Eh). A TXD1 or TXD2 pulse is internally extended (TXDEXT) by time tINITR1 to inhibit the latching of low alarms and warnings related to the APC loop to allow for the loop to stabilize. The nonlatching alarms and warnings are TXP LO, BMON1 LO, BMON2 LO, PMON1 LO, and PMON2 LO. In addition, TXP LO is disabled from creating FETG. See the Transmit Fault (TXFOUT) Output section for a detailed explanation of TXFOUT. As shown in Figure 9, the same signals and faults can also be used to gener-ate the internal signal FETG. FETG is used to send a fast “turn-off” command to the laser driver. The intended use is a direct connection to the laser driver’s TXD1, TXD2 input if this is desired. When VCC < POA, TXDOUT1 and TXDOUT2 are high impedance.

Figure 10. Logic Diagram 2

IC datasheet pdf-DS1876,pdf (SFP Controller with Dual LDD Interface)

Six digital input pins and five digital output pins are pro-vided for monitoring and control.

Digital I/O Pins

IN1, RSEL, OUT1, RSELOUT

Digital input pins IN1 and RSEL primarily serve to meet the rate-select requirements of SFP and SFP+. They can also serve as general-purpose inputs. OUT1 and RSELOUT are driven by a combination of the IN1, RSEL, and logic dictated by control registers in the EEPROM (see Figure 10). The levels of IN1 and RSEL can be read from the STATUS register (Lower Memory, Register 6Eh). The open-drain output OUT1 can be controlled and/or inverted using the CNFGB register (Table 02h,

18 _____________________________________________________________________________________

上一页第18页

你可能喜欢

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email