IC datasheet pdf-DS1876,pdf (SFP Controller with Dual LDD Interface)
SFP Controller with Dual LDD InterfaceDS1876
of SCL during a bit read. The device shifts out each bit of data on SDA at the falling edge of the previous SCL pulse and the data bit is valid at the rising edge of the current SCL pulse. Remember that the master generates all SCL clock pulses, including when it is reading bits from the slave.
Acknowledgement (ACK and NACK): An acknowl-edgement (ACK) or not-acknowledge (NACK) is always the 9th bit transmitted during a byte transfer. The device receiving data (the master during a read or the slave during a write operation) performs an ACK by transmitting a zero during the 9th bit. A device per-forms a NACK by transmitting a one during the 9th bit. Timing (Figure 12) for the ACK and NACK is identical to all other bit writes. An ACK is the acknowledgment that the device is properly receiving data. A NACK is used to terminate a read sequence or as an indication that the device is not receiving data.
Byte Write: A byte write consists of 8 bits of informa-tion transferred from the master to the slave (most significant bit first) plus a 1-bit acknowledgement from the slave to the master. The 8 bits transmitted by the master are done according to the bit write definition and the acknowledgement is read using the bit read definition.
Byte Read: A byte read is an 8-bit information transfer from the slave to the master plus a 1-bit ACK or NACK from the master to the slave. The 8 bits of information that are transferred (most significant bit first) from the slave to the master are read by the master using the
bit read definition, and the master transmits an ACK using the bit write definition to receive additional data bytes. The master must NACK the last byte read to terminate communication so the slave returns control of SDA to the master.
Slave Address Byte: Each slave on the I2C bus responds to a slave address byte sent immediately following a START condition. The slave address byte contains the slave address in the most significant 7 bits and the R/W bit in the least significant bit.
The DS1876 responds to three slave addresses. The auxiliary memory always responds to a fixed I2C slave address, A0h. (If the main device’s slave address is programmed to be A0h, access to the auxiliary memory is disabled.) The Lower Memory and Tables 00h–06h respond to I2C slave addresses whose lower 3 bits are configurable (A0h–AEh, B0h-BEh) using the DEVICE ADDRESS byte (Table 02h, Register 8Bh). The user also must set the ASEL bit (Table 02h, Register 88h) for this address to be active. By writing the cor-rect slave address with R/W = 0, the master indicates it writes data to the slave. If R/W = 1, the master reads data from the slave. If an incorrect slave address is written, the DS1876 assumes the master is communi-cating with another I2C device and ignores the com-munications until the next START condition is sent.Memory Address: During an I2C write operation to the DS1876, the master must transmit a memory address to identify the memory location where the slave is to store the data. The memory address is
Figure 12. I2C Timing

20 _____________________________________________________________________________________
IC datasheet pdf-DS1877,pdf,datasheet,SFP Controller for Dual Rx Interface_信息与通信_工程科技_专业资料。IC datasheet pdf-DS1877,pdf,datasheet,SFP ...
IC datasheet pdf-ONET8531T,pdf(11.3Gbps ...ONET8531T With Dual Cathode PIN Diode Copyright ?...Products DSP Clocks and Timers Interface Logic ...
元器件交易网www.cecb2b.com Datasheet 8 Gbps Bi...(Duplex LC) Dual-fiber, bi-directional Class 1...2-wire Serial Interface Data Line (MOD-DEF2) ...
? Customer’s MAC should be setup for SGMII interface with Auto-Negotiation... IC datasheet pdf-DS187... 65页 免费 AN4138C(20G四通道SFP有... 20页 ...
datasheet 11页 免费 XFP模块电路设计 6页 1下载...Assembled with low EMI emissions IC and fully ...Interface GBIC 1000Base-X to 1000Base-T SFP-...
IC datasheet pdf-DS1876,... 69页 免费 AlGaNGaN+HEMT的研制 60页 免费 ... Normally Off AlGaNGaN Low-Density Drain HEMT (LDD-HEMT) With Enhanced ...
The resistor range for the laser current settings is optimized to interface with the DS1858 SFP controller IC. The MAX3735/MAX3735A provide transmit-...
interface Duplex LC connector Built-in digital ...Datasheet Digital Diagnostics Functions MRV’s SFP-...Controller (DDTC) inside the transceiver, which ...
dual-loop LDD, allowing one PC board layout to...APPLICATIONS 1×/2×/4× Fibre Channel SFP/SFF...Control with a Single-Ended Laser Interface Rev....
Datasheet MAX3735 - 2.7Gbps, Low-Power SFP Laser Drivers - Maxim ... settings is optimized to interface with the DS1858 SFP controller IC. ...
热门文档