Free shared information published by International Association of Classification Societies.
No.47 Shipbuilding and Repair Quality Standard
(1996)
(Rev. 1, 1999)
(Rev.2, Dec. 2004)
Part A Shipbuilding and Repair Quality Standard for New Construction
Part B Repair Quality Standard for Existing Ships
PART A - SHIPBUILDING AND REPAIR QUALITY STANDARDS FOR NEW CONSTRUCTION
1. Scope
2. General requirements for new construction 3. Qualification of personnel and procedures
3.1 Qualification of welders
3.2 Qualification of welding procedures 3.3 Qualification of NDE operators
4. Materials
4.1 Materials for structural members 4.2 Under thickness tolerances 4.3 Surface conditions
5. Cutting
5.1 Gas cutting
5.2 Plasma arc cutting 5.3 Laser beam cutting
6. Fabrication and fairness
6.1 Flanged longitudinals and flanged brackets 6.2 Built-up sections 6.3 Corrugated bulkheads
6.4 Pillars, brackets and stiffeners
6.5 Maximum heating temperature on surface for line heating 6.6 Block assembly
6.7 Special sub-assembly 6.8 Shape
6.9 Fairness of plating between frames 6.10 Fairness of plating with frames
6.11 Preheating for welding hull steels at low temperature
7. Alignment 8. Welding
8.1 Typical butt weld plate edge preparation (manual welding) 8.2 Typical fillet weld plate edge preparation (manual welding) 8.3 Typical butt and fillet weld profile (manual welding) 8.4 Lap, plug and slot welding 8.5 Distance between welds 8.6 Automatic welding
9. Repair
9.1 Typical misalignment repair
9.2 Typical butt weld plate edge preparation repair (manual welding) 9.3 Typical fillet weld plate edge preparation repair (manual welding) 9.4 Typical fillet and butt weld profile repair (manual welding) 9.5 Distance between welds repair 9.6 Erroneous hole repair 9.7 Repair by insert plate 9.8 Weld surface repair
REFERENCES
. 1 August 1999) Part A Part B Shipbuilding and Repair Quality Standard for New Construction Repair Quality Standard for Existing Ships 47-1 IACS Rec. ...
? - 1 - No.47 Shipbuilding and Repair Quality Standard (1996) (Rev. 1...to be remedied by grinding and/or welding in accordance with IACS Rec.12...
. 1 August 1999) Part A Part B Shipbuilding and Repair Quality Standard for New Construction Repair Quality Standard for Existing Ships 47-1 IACS Rec. ...
IACS-Rec.47(2012版)_交通运输_工程科技_专业资料。最新更新的IACS 47号建议案No.47 Shipbuilding and Repair Quality Standard (1996) (Rev. 1, 1999) (...
. 1 August 1999) Part A Part B Shipbuilding and Repair Quality Standard for New Construction Repair Quality Standard for Existing Ships 47-1 IACS Rec. ...
船舶IACS标准_专业资料。船舶建造中的装配及完工质量标准No.47 Shipbuilding and Repair Quality Standard (1996) (Rev. 1, 1999) (Rev.2, Dec. 2004) (Rev...
shipbuilding NDT standards (CB/T) with IACS REC...and quality classification) 在 IACS URZ23 和 ...in an application standard. 经合同各方商定, 表 ...
c) Builder's standards, and Builder's standard practice d) IEC e) IACS 47, part A: shipbuilding and repair quality standard for new construciton 3. ...
手工电弧焊坡口形状和公差范围 SMAW Groove preparation and tolerance limits 内...IACS 船舶建造和修理质量标准 IACS shipbuilding and repair quality standard ABS...
Rec 47 Rev.7 (June 2013)_HF_交通运输_工程科技_专业资料。IACS History ... Part A Recommendation No.47 “Shipbuilding and Repair Quality Standard” ...
热门文档