外文翻译




J. Mater. Sci. Technol., Vo]A8 No.6, 2002
547
Table 3 Effect of composition on density of forged compacts
Sample No.
1 2 3 4 5
6
Fe-C
7.54 7.60 7.56 7.59 7.59 7.60
Fe-C-Ni-Mo
7.59 7.63 7.62 7.63 7.65 7.65
Fe-C-Cu 7.62 7.64 7.61 7.65 7.64 7.66
Fe-C-Cu-Mo
7.68 7.69 7.65 7.79 7.69 7.70
Ni-Mo alloy
7.64 7.66 7.64 7.65 7.64 7.65
Table 4 Mechanical properties of powder forged connecting rod after heat treatment
Powder forging rod 2OCrMo rod produced with traditional method
Hardness(HRC) Strength
Large end Crank Small end /MPa
31.5 965 62.0 61.0
980 6064 3045 6064
Impact
/(J/cm2) 24.7 29.4
Density /(g/cm3)
7.7
7.8
7.80 7.72

7.64 7.56 7,48 7.40
85()
900
950
1000
1050
1100
1150
Forging temperature / t
Fig.8 Effect of the forging temperature on density of the
forged rod

Fig.10 Microstructure of the sintered compact and the forged
rod (a) sintered compact, (b) forged rod
Fig.9 Effect of the preform density on that of the forged
rod

in Fig.1O. From Fig.1O, it can be seen that powder forging can eliminate pores significantly and obtain an even and fine microstructnre.
In order to satisfy the final dimensions and properties of the rod, the forged compact needs hole drilling, heat treat-
ment, and fine milling. The heat treatment process (as shown in Fig.11) inclndes carburization, qnenching and tempering. In order to compare with a rod prodnced with the traditional method, the mechanical properties of the powder forging con-
necting rod after heat treatment were measured. The impact experimental sample was produced to the national standard sample—Charpy U-shape sample with a notch. The measnred results are shown in Table 4. The physical and mechanical properties are the same as that of a 2OCrMo steel rod used in present. The powder forging method can be substituted for the traditional method nsing 2OCrMo steel to fabricate the connecting rod completely.
Time I h
Fig.11 Carburization, quenching and tempering process
After heat treated through carburization, quenching and tempering, the microstructure of the forged compact was ex-
amined by the optical microscope, as shown in Fig.t2. It was composed of low carbon marten.site, pearlite and ferrite. The structure was fine and even.
After full experiments were finished, the Fe-C-Cu-Mo powder forging connecting rod was fixed on a motor engine produced by QingQi group. 100 h durable experiment was conducted by an internal combustion engine research insti-
tute of Shandong province. No abnormal phenomena were discovered for the powder forging connecting rods. The load-
– by forging – by casting – by powder metallurgy(粉末冶金) – by ...removing flash Figure 14.7 (a) Stages in forging a connecting rod for ...
Costs of a Rod Made by Forging and Casting Figure 14.19 Relative unit costs of a small connecting rod made by various forging and casting processes. ...
powder metallurgy or casting, or a preformed blank from a prior forging ...s shape gradually changes, as shown for the forging of a connecting rod....
Powder+Forging+of+a+Mo... 暂无评价 6页 1下载券 Connecting rod is an i... 2页 免费 The Finite Element Ana... 4页 2下载券 connecting rod(曲柄连...
[2] Q.L. Luo, Improved production technology of motorcycle forgings, ...Lei, New technology for precision forging of connecting rod, J. Jinan Univ...
Costs of a Rod Made by Forging and Casting Figure 14.19 Relative unit costs of a small connecting rod made by various forging and casting processes. ...
PowderForgingofaMotorcycleConnectingRod 隐藏>> 5 44 J . t Ma e r . Sei . e T e hn o l厂 b l18 V . . N o . 6 , 2002 P G w o u ...
Diesel engine connecting rod processing Abstract The connecting rod is one of...Two holes can not directly, forging Work. By looking at more than ...
Gripping Mechanism of Forging Manipulator Structure Composition. The gripping mechanism is made up of pushing rod, connecting rod, clamp and clamping cylinder...
Conrod_机械/仪表_工程科技_专业资料。connecting rod manufacturing processJanuary...densification of a heated powder-based preform using a single forging strike...
热门文档