外文翻译
548 J. Mater. Sci. Technol., Vol.18 No.6, 2002

Fig.12 Metallograph of the forged rod after heat treatment ing experiment showed that the forged P/M connecting rod has satisfied its working requirement completely.
Compared with the current fabricating method, the pow-
der forging process of the P/M connecting rod not only can control the powder weight accurately but also can avoid some defects caused in the traditional process and improve the me-
chanical properties. Further more, the powder forging process can save much material, reduce the equipment capacity and remove the excessive machining including cropping, trimming, hole drilling and polishing. The fabrication cost is reduced obviously.
4. Conclusions
(1) Powder forging of the motorcycle connecting rod is an
advanced process combining the advantages of powder metal-
lurgy and precision forging. It can satisfy the requirement on mechanical properties and working conditions of the connect-
ing rod. The experimental results showed that the connecting rod produced by the powder forging process is reliable for ap-
plication in motorcycle engines.
(2) Fe-C-Cu-Mo alloy powder can exhibit excellent physi-
cal and mechanical properties during consolidating, sintering and powder forging. It can be substituted for 2OCrMo steel to fabricate the connecting rod completely.
(3) The powder forging process of the connecting rod can save much material, reduce the equipment capacity and re-
move the excessive machining.
(4) The research results of powder forging the P/M mo-
torcycle connecting rod can provide a good reference to the powder forging of automobile connecting rods.
Acknowledgement
This work was supported by Shandong Province Natural Sci-
ence Fund and Shandong Province Outstanding Young Scientists Fund Grant.
REFERENCES
[1] Guanghan QIU: The Chinese Journal of Nonferrous Metals,
1996, 6(2), 117. (in Chinese)
[2] G.C.Wang, G.Q.Zhao and Y.X.Jia:
Trans. Nonferrous Met.
Soc. China, 2000, 10(1), 84.[3 [4 1 1 P.K.Johnson: mt. J. Powder Metall., 1996, 32(2), 145.
G.Ashok, K.Jinka and M.Bellot: 255.
mt. J. Powder Metall., 1996,32(3),
[5] Z.J.Liu, X.H.Qu and B.Y.Huang: Trans. Nonferrous Met. Soc.
China, 1997, 7(1), 96.
– by forging – by casting – by powder metallurgy(粉末冶金) – by ...removing flash Figure 14.7 (a) Stages in forging a connecting rod for ...
Costs of a Rod Made by Forging and Casting Figure 14.19 Relative unit costs of a small connecting rod made by various forging and casting processes. ...
powder metallurgy or casting, or a preformed blank from a prior forging ...s shape gradually changes, as shown for the forging of a connecting rod....
Powder+Forging+of+a+Mo... 暂无评价 6页 1下载券 Connecting rod is an i... 2页 免费 The Finite Element Ana... 4页 2下载券 connecting rod(曲柄连...
[2] Q.L. Luo, Improved production technology of motorcycle forgings, ...Lei, New technology for precision forging of connecting rod, J. Jinan Univ...
Costs of a Rod Made by Forging and Casting Figure 14.19 Relative unit costs of a small connecting rod made by various forging and casting processes. ...
PowderForgingofaMotorcycleConnectingRod 隐藏>> 5 44 J . t Ma e r . Sei . e T e hn o l厂 b l18 V . . N o . 6 , 2002 P G w o u ...
Diesel engine connecting rod processing Abstract The connecting rod is one of...Two holes can not directly, forging Work. By looking at more than ...
Gripping Mechanism of Forging Manipulator Structure Composition. The gripping mechanism is made up of pushing rod, connecting rod, clamp and clamping cylinder...
Conrod_机械/仪表_工程科技_专业资料。connecting rod manufacturing processJanuary...densification of a heated powder-based preform using a single forging strike...
热门文档