文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 机械/仪表 > How to Measure Flatness with Optical Flats
侵权投诉

How to Measure Flatness with Optical Flats

平面平晶检测平面度

Hold the optical flat steady with one hand and draw the paper out from between the work piece and the optical flat with the other hand. If bands do not appear, repeat this procedure. This will reduce the possibility of scratching the optical flat and the workpiece--as in scrubbing both

pieces together. The bands should be viewed from a distance at least 10 times the diameter of the optical flat and with the line of vision as nearly perpendicular to the flat as possible. If the bands are straight, parallel and evenly spaced, the surface is flat. If the bands are curved or are unevenly spaced, the surface is not flat.

If Bands Fail to Appear

If the Bands fail to appear it may be due to one of the following reasons: Dust, burrs or nicks are still holding the optical flat away from the surface. Do not slide the optical flat around on the surface in an effort to make the bands appear as this may scratch the flat. Instead, try again after recleaning the surface or removing the burrs.

The wedge between the surface of the work and the optical flat may be: Too thick. Press down on the optical flat with a uniform pressure to squeeze out the air film. Too thin. If moisture or oil is present if may cause the optical flat to wring or adhere to the work so closely that bands cannot appear. Too angular.

The flat may be making too great an angle with the work, in which case the bands will be so close together as to be nearly invisible. Try putting pressure at different points around the edge of the optical flat. Too nearly parallel. This rarely occurs. In this case however, the bands would be so far apart that they would not be distinguishable as bands.

Amount of Flatness Error

The amount that the bands curve, with reference to the distance between them, indicates the amount of flatness error. In judging the amount of curvature, imagine a line drawn across the surface from one end of any band to the other end of that same band.

If this line just touches the previous band the flatness error is 1 band ( see figure 2a ). If it comes half way between the two bands the error is 1/2 band ( see figure 2b ). If the surface is out of flat two bands the line will just touch the second band, if it is out 3 bands it will just touch the third band and so on.

In practice the imaginary line may be made real by aligning a piece of fine wire or thread across the face of the monochromatic lights diffusion screen with the ends of the band, or by use of a transparent straight-edge.

Convex or Concave?

The rule for determining whether a surface is concave or convex is as follows: If the bands curve around the thin part of the wedge (contact or pressure point) the surface is convex. If they curve around the thick part of the wedge the surface is concave.

Irregular Surface

Where the surface to be measured is irregular, the contact method of flatness testing is

recommended. Here the flat is placed in the most intimate possible contact with the work piece;

- 2 -

上一页第2页

你可能喜欢

热门文档

相关文档

  • 光学平板

    The determination of the flatness of any ...in the fringes to measure the surface accurately....with repeated use, optical flats can lose their ...

  • 南开大学光学工程内部课件Oct 28th

    l, the optical path length is change by l and...Typical Measurement Results – Flatness/Shape – ...To measure the temporal coherence, we need detect...

  • 近代光学 12-Oct 22nd

    Interferometer is the optical setup which split ...Typical Measurement Results – Flatness/Shape – ...To measure the temporal coherence, we need detect...

  • Bowl Feed Technique

    amounts, the figure, i.e., flatness of the surface, may be well ...In order to measure surface roughness on polished optical flats, multiple ...

  • Bowl Feed Technique

    amounts, the figure, i.e., flatness of the surface, may be well ...In order to measure surface roughness on polished optical flats, multiple ...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email