文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 机械/仪表 > How to Measure Flatness with Optical Flats
侵权投诉

How to Measure Flatness with Optical Flats

平面平晶检测平面度

by Van Keuren

Introduction

The easiest and best way to test the flatness of a flat lapped or polished surface is with an optical flat. Such surfaces are found on micrometers, measuring machines, gage blocks, snap gages, ring seals, valve seats and precision flat lapped parts.

The surface must be sufficiently finished to reflect light; ordinary ground surfaces are too

irregular to show light wave interference bands. However, unless the material is extremely soft or porous, a few rubs on a flat lap will smooth off the top of the grinding ridges and enable bands to be seen in monochromatic light.

The Phenomenon of Interference Bands

When there is an extremely thin wedge between two flat surfaces a series of interference bands or fringes appear. The bands occur at right angles to the slope of the wedge. They represent

intervals of approximately 11.57 millionths of an inch (293.8 nanometers) from the surface being tested to the optical flat when a monochromatic light of 23.13 millionths (587.6 nm) wave length is used.

The Van Keuren series of helium monochromatic light sources provide a highly diffused light of this wave length. Dark bands occur because light reflections from the two surfaces which form the wedge interfere with each other where the thickness of the wedge is one half or multiples of one half the wave length of the light. The parallel bands thus form at zones where the wedge thickness changes by 1/2 wave length. Between each pair of dark bands the reflections reinforce each other and produce bright bands. When viewed perpendicularly in helium light, the dark

bends are located where the air wedge thickness changes by equal intervals of .00001157" (293.8 nm).

Procedure For Making Flatness Tests

Remove the dust from the surface of the work and the optical flat with a camel hair brush. Burrs and nicks should be removed by using an appropriate deburring stone. Place the work under the monochromatic light. Place a clean piece of optical tissue (or any other clean paper) over the work piece. Place the optical flat on top of the paper; the optical flat may be on the bottom in cases where a reflex light is used.

How to Measure Flatness with Optical Flats

- 1 -

第1页

你可能喜欢

热门文档

相关文档

  • 光学平板

    The determination of the flatness of any ...in the fringes to measure the surface accurately....with repeated use, optical flats can lose their ...

  • 南开大学光学工程内部课件Oct 28th

    l, the optical path length is change by l and...Typical Measurement Results – Flatness/Shape – ...To measure the temporal coherence, we need detect...

  • 近代光学 12-Oct 22nd

    Interferometer is the optical setup which split ...Typical Measurement Results – Flatness/Shape – ...To measure the temporal coherence, we need detect...

  • Bowl Feed Technique

    amounts, the figure, i.e., flatness of the surface, may be well ...In order to measure surface roughness on polished optical flats, multiple ...

  • Bowl Feed Technique

    amounts, the figure, i.e., flatness of the surface, may be well ...In order to measure surface roughness on polished optical flats, multiple ...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email