一;润滑油和煤油的润滑比例是:3:1 2、利用水压法检查汽缸体裂纹,应在 392Mpa 压力下,保持 15 分钟无渗漏 3、柴油机进气门杆部与导管的配合间隙为:0.006——0.107MM 4、柴油机排气门杆部与导管的配合间隙为:0.075——0.127MM 5、柴油机摇臂衬套与摇臂轴的间隙规定为:0.024——0.007MM 6、安装新气门座圈时,为方便装入,可将柴油机缸盖放在机油 中预热至:150——170摄氏度再压入新座圈
65, when the diesel engine is gear wear more than the tooth thickness: 0.25MM should be replaced
66, diesel engine timing gear keyway wear, in the old keyway into: 120 degrees to open the new slot
67, plunger coupled parts sliding experiments, should be perpendicular to the plunger out from the sleeve :40 - 50MM, put
Next after the free fall, slide the situation
68, in the diesel fuel injection pump camshaft cam surface wear no more than: 0.5MM, it would be a special convex Grinding wheel grinder
69, diesel fuel injection pump camshaft keyway wear, can be separated in the original keyway: 180 degrees to open the new slot
70, by grinding flat grooves of diesel fuel injection pump roller body adjusting screw more than: 0.5MM
Cut light the whole plane, and then chrome-plated repair.
71, diesel fuel injection pump roller body oriented surface and the bore with the gap exceeds: 0.2MM When the can twist
Cut the seat hole chrome-plated repair-oriented decent column
72,190 injection pump camshaft axial clearance requirements for :0.2 - 0 .4 MM
73,190 injection pump plunger and barrel assembly installation, move up and down as :0.5 - 1MM
74,190 mechanical system governor, the flying iron to open the largest diameter: 104MM
75, the governor pressure regulator spring minimum free length can not be shorter than the prescribed length: 5% 76, in the rotational speed of 1,500 rpm, the cycloid rotor pump's displacement: 0.242L / S, indicating that the Pump in good condition
77, do diesel delivery valve sliding experiment, the outlet valve seat out: 1/3, let go
To see its free-fall slide situation
78, cycloid rotor input requirements of pump seal experiment in the next the: 0.392Mpa hydraulic: 3
Minutes without leakage for qualified
79, cycloid rotor pump inside and outside the rotor face appear larger than: 0.10MM deep scratches should be replaced 80, cycloid rotor pump rotor shaft keyway damage, in the old keyway apart: 90 degrees to open the new slot
81, cycloid rotor pump inside and outside the rotor shaft journal wear is greater than: the 0.08MM When reaming can be used,
Chrome-plated to increase the journal size to repair
82, the water tank of diesel cooling pipe scale can be used to contain 10% - 15% caustic soda solution, heated dip Cook :25 - 30 minutes
83, the welding block the water pipe, a maximum of 10%
84,190 cooling water pump shaft bending over: 0.05 MM when cold press straightening
85, after the pump keyway damage can be with the old keyway :20 - 90 degrees apart to open a new groove
86, the pump cracks, perforation, at the ends of each turn diameter: 2.5MM stop hole, and then oxygen welding repair 87, water pump impeller on the back and the pump casing axial gap :1.0 - 1 .3 the MM
88, the pump of leaves and water flange end clearance :0.8 - 1.0 MM
89,190 pump performance requirements: speed: 2863r/min, the pump displacement is greater than or equal to: For the normal 16. 7L / S
90, under normal circumstances, the water temperature increases to: 72 ° C, the diesel engine thermostat bellows tube should
Side of the hole to close the main valve is fully open
91, the cooler diesel engine after the repair should be carried out: 192Kpa water pressure seal experiment
92, the provisions of diesel gear oil pump gear cylindrical pump body between the inner wall of the gap :0.43 - 0.495MM, when measuring with a feeler, and its value :0.215 - 0 .243 MM
93,190 diesel gear oil pump, gear meshing gap :0.15 - 0 .30 the MM
94,190 diesel gear oil pump, gear end clearance :0.18 - 0 .25 the MM
95, the number of the oil cooler blocked tube can not exceed: 5
南京富电康机电工程有限公司依维柯发电机 依维柯发电机:意大利依维柯公司生产的发电...专业提供依维柯柴油发电 机组的维修 2 提供依维柯柴油发电机组的大修,中修. 3 ...
电气技术工程师,承接各类柴油发 电机组(如康明斯、曼、依维柯、珀金斯、奔驰、三菱、大宇、卡特、电友、日野等)的维修保养业务,能够迅 速准确的诊断发电机组故障并...
新建RTF 格式 (3)依维柯... 2页 免费 意大利依维柯柴油发电机... 8页 ...轮胎的使用与保养 七、行驶系常见故障诊断 一、行驶系的拆卸 1.前悬架的拆卸 ...
柴油发电机组维修日兴动力承接:康明斯 珀金斯 依维柯 大宇 富豪 三菱 奔驰 卡特 强鹿 上柴 潍柴 玉柴等进口及国产机组特约维 修、保养服务。公司可与客户签订长期...
美国科勒柴油发电机组维修保养_电力/水利_工程科技_专业资料。凸轮盘:146220-... 无锡无动柴油发电机组维... 意大利依维柯柴油发电机... 宁波柴油发电机组维修...
发电机组保养公司具有一批专业维修保养服务人员,在行业内超过十五年的柴油发动机/电气技术工程师,承接各类柴油发电机组 (如康明斯、曼、依维柯、珀金斯、奔驰、三菱、...
柴油发电机维修_机械/仪表_工程科技_专业资料。宁波日兴动力科技有限公司 由于...珀金斯 依维柯 大宇 富豪 三菱 奔驰 卡特 等进口及国产机组特约维修、保养服务。...
世界名牌柴油发电机组对比_电子/电路_工程科技_专业...可靠性高 省却繁琐的维修保养 配有保护装置,确保运作...十三. 依维柯(IVECO)公司 依维柯(IVECO)公司是意大利...
依维柯·爱福 为依维柯公司专为客户生产特种柴油机的公司,位于意大利米兰市,其...维修方面,公司主要成员是具有十多年发电设备维修的专业工程师。有着多年专业维修...
国内柴油发电机组概述_电力/水利_工程科技_专业资料...后通过与欧洲发动机工厂IVECO\VOLVO\SCANIA\等合作,...? PRMAC 意大利知名设备生产商,在欧洲意大利、德国...
热门文档