一;润滑油和煤油的润滑比例是:3:1 2、利用水压法检查汽缸体裂纹,应在 392Mpa 压力下,保持 15 分钟无渗漏 3、柴油机进气门杆部与导管的配合间隙为:0.006——0.107MM 4、柴油机排气门杆部与导管的配合间隙为:0.075——0.127MM 5、柴油机摇臂衬套与摇臂轴的间隙规定为:0.024——0.007MM 6、安装新气门座圈时,为方便装入,可将柴油机缸盖放在机油 中预热至:150——170摄氏度再压入新座圈
35, various diesel engine piston ring openings should be staggered: 120 degrees
36, Z12V190B type of diesel engine piston pin with the pin bore standard size is: -0.02
- 0.008MM
37, outer diameter 000-foot shaft rod pitch: 0.5MM
38, in the grinding of diesel engine valve cone middle ring when the valve seat belt :1.5 -
2.5MM wide continuous contact zone can be considered qualified
39, if the diesel engine valve contacts while on the side of the loop bandwidth should be used: 15 reamer dressing 40, diesel engine valve and partial contact with the ring bandwidth should be used: 75 ° reamer dressing
41, the identification method of Hongdan oil test valve sealing performance, the rotary valve: 1/4 turn.
Then lift the valve to check
42, diesel engine, linkage machine base plane parallel to the degree of error per meter shall not be greater than: 0.5MM
43, the installation of diesel, the pressure plate bolts not less than: 6
44, when you install the engine room base, generally be installed on the 4th base, on the 4th base before and after the two actually mouth
The center mark and the wellhead Alignment alignment, the deviation can not be greater than: positive and negative 5MM
45, diesel engine crankshaft runout is greater than: the 0.06MM should replace the crankshaft, or conduct
Straightening repair
46, diesel engine crankshaft bending deformation is generally greater than: 0.1MM when should the school direct
47,. 0.3MM, and the shaft diameter with the gap is allowed if the diesel engine bearing alloy layer thickness is greater than:
Within the bearing surface has a small number of annular grooves, you can continue to use
48, in the measurement of diesel engine bearing inner diameter with an inner diameter dial indicator should be measured at each position: 2
Direction
49, the height of the bearing of diesel engine, higher than the bearing plane :0.05-0 .10 MM appropriate
50, in scraping the diesel engine bearing, the bearing contact area of each channel reach: more than 75% is qualified 51,190 diesel engine crankshaft, to run: 980Kpa pressure: 5 minutes, the first ends
No leaks
52, when the bulk of the cone of diesel engine valve wear scar depth of more than: 1MM, should be scrapped 53, when the diesel engine valve stem diameter wear over: 0.6 MM, should be scrapped
54,190 diesel engine intake valve head end of the plane and the cylinder head plane distance :1.7 - 3MM
55,190 diesel engine exhaust valve head end of the distance between the plane and the cylinder head plane :1.7 - 2 .66 MM
56, when the diesel engine camshaft diameter and the bearing hole between the gap value is greater than: 0.3MM should repair
More than 57,190 camshaft diameter circle to the beat error: 0.05 MM should be repaired
58, when the use of templates to check diesel tappet spherical wear, when the light leakage is greater than: 0.02MM , Should be repaired
59, when the diesel roller rocker bushings and rocker shaft gap beyond: 0.20MM should be replaced with bushings 60, diesel engine rocker shaft bending over: 0.1MM should be cold pressing alignment
Alignment of 61, when the diesel engine putting bending over: 0.5MM, should be cold pressing
62, diesel engine timing gear radial swing differential can not exceed: 0.04MM
63, diesel flat tappet and the bore with the gap from the value should be: 0.02-
0.03MM range
64,190 diesel engine valve rocker arm and rocker shaft with the clearance provisions for :0.12 - 0 .17 the MM Within the
南京富电康机电工程有限公司依维柯发电机 依维柯发电机:意大利依维柯公司生产的发电...专业提供依维柯柴油发电 机组的维修 2 提供依维柯柴油发电机组的大修,中修. 3 ...
电气技术工程师,承接各类柴油发 电机组(如康明斯、曼、依维柯、珀金斯、奔驰、三菱、大宇、卡特、电友、日野等)的维修保养业务,能够迅 速准确的诊断发电机组故障并...
新建RTF 格式 (3)依维柯... 2页 免费 意大利依维柯柴油发电机... 8页 ...轮胎的使用与保养 七、行驶系常见故障诊断 一、行驶系的拆卸 1.前悬架的拆卸 ...
柴油发电机组维修日兴动力承接:康明斯 珀金斯 依维柯 大宇 富豪 三菱 奔驰 卡特 强鹿 上柴 潍柴 玉柴等进口及国产机组特约维 修、保养服务。公司可与客户签订长期...
美国科勒柴油发电机组维修保养_电力/水利_工程科技_专业资料。凸轮盘:146220-... 无锡无动柴油发电机组维... 意大利依维柯柴油发电机... 宁波柴油发电机组维修...
发电机组保养公司具有一批专业维修保养服务人员,在行业内超过十五年的柴油发动机/电气技术工程师,承接各类柴油发电机组 (如康明斯、曼、依维柯、珀金斯、奔驰、三菱、...
柴油发电机维修_机械/仪表_工程科技_专业资料。宁波日兴动力科技有限公司 由于...珀金斯 依维柯 大宇 富豪 三菱 奔驰 卡特 等进口及国产机组特约维修、保养服务。...
世界名牌柴油发电机组对比_电子/电路_工程科技_专业...可靠性高 省却繁琐的维修保养 配有保护装置,确保运作...十三. 依维柯(IVECO)公司 依维柯(IVECO)公司是意大利...
依维柯·爱福 为依维柯公司专为客户生产特种柴油机的公司,位于意大利米兰市,其...维修方面,公司主要成员是具有十多年发电设备维修的专业工程师。有着多年专业维修...
国内柴油发电机组概述_电力/水利_工程科技_专业资料...后通过与欧洲发动机工厂IVECO\VOLVO\SCANIA\等合作,...? PRMAC 意大利知名设备生产商,在欧洲意大利、德国...
热门文档