一;润滑油和煤油的润滑比例是:3:1 2、利用水压法检查汽缸体裂纹,应在 392Mpa 压力下,保持 15 分钟无渗漏 3、柴油机进气门杆部与导管的配合间隙为:0.006——0.107MM 4、柴油机排气门杆部与导管的配合间隙为:0.075——0.127MM 5、柴油机摇臂衬套与摇臂轴的间隙规定为:0.024——0.007MM 6、安装新气门座圈时,为方便装入,可将柴油机缸盖放在机油 中预热至:150——170摄氏度再压入新座圈
96, the oil cooler seal experimental requirements for: 294Kpa pressure or 980Kpa hydraulic under 5 minutes Do not drain as qualified
97 diesel engine performance deterioration of one of the symbols is: when the temperature is normal, the cylinder pressure is less than the required pressure
Force: 70%
98, the use of remote auscultation method to determine the diesel engine failure, the staff to distance diesel :20-30M 99, under normal circumstances, the diesel engine should normally be: within 5 seconds of smooth start
100, scraping the diesel engine bearing, the angle between knife track and tile centerline as follows: 45 degrees 101, diesel engine bearing scraping Scraping points requirements: 25 * 25 mm2 range of not less than: 6:00 102, welding welding repair the engine body cracks, preheat the body, the preheating temperature: 600 -
-700 ° C
103, using acetylene welding repair diesel engine body, the first body warm-up to: 500 ° C, welding in
Insulation: 500 - 550 degrees 1 hour
104, the use of screws to fill the crack of Repair of diesel engine body, cut off after the screws to be higher than the body: 1 -
-1.5MM
105, fill plate method to repair the diesel engine body cracks, fill the board cut into a crevasse outline is similar to, greater than four weeks
Break 15 - 20MM appropriate
106, the experimental test of the fuel injection pump, the indoor temperature is best controlled at: 20 plus or minus 5 degrees
107, the fuel injection pump fuel injection quantity inspection to the plunger vice complete: 400 stroke
108, the run-in run time of the injection pump as 3 - 5 minutes
109, the fuel injection pump running when the fuel temperature should be controlled in 40 to - 45 ° C
110,190 Series Pistons and Rods perpendicularity requirements: 100MM, the error can not be
In 0.05MM
111, crane travel cars using the process of bearing temperature should not exceed: 70 ° C
112, overheating of the turntable is usually more than its temperature: 70 degrees Celsius
113, diesel fuel mixture to the formation of a very short time, accounting for about :15 - 35 degrees crank angle 114, diesel from the fuel injected into the cylinder to the firing ended, generally only 0.001 - 0.004 seconds
115, the speed of the burning period is generally the end of the piston to leave the only point :6 - 10 degrees crank angle
116, in the vortex combustion chamber, swirl chamber volume about the diesel engine combustion chamber volume: 60%
117, diesel engine adaptation coefficient :1.015 - 1.10
The best use of the dynamic range of 118,190 diesel engines :588 - 809KW
119, the cleaning part of the alkaline solution required the solution was heated to :80 - 90 degrees Celsius
120 Clear method to remove coke chemical, spare parts required in the solution immersed
南京富电康机电工程有限公司依维柯发电机 依维柯发电机:意大利依维柯公司生产的发电...专业提供依维柯柴油发电 机组的维修 2 提供依维柯柴油发电机组的大修,中修. 3 ...
电气技术工程师,承接各类柴油发 电机组(如康明斯、曼、依维柯、珀金斯、奔驰、三菱、大宇、卡特、电友、日野等)的维修保养业务,能够迅 速准确的诊断发电机组故障并...
新建RTF 格式 (3)依维柯... 2页 免费 意大利依维柯柴油发电机... 8页 ...轮胎的使用与保养 七、行驶系常见故障诊断 一、行驶系的拆卸 1.前悬架的拆卸 ...
柴油发电机组维修日兴动力承接:康明斯 珀金斯 依维柯 大宇 富豪 三菱 奔驰 卡特 强鹿 上柴 潍柴 玉柴等进口及国产机组特约维 修、保养服务。公司可与客户签订长期...
美国科勒柴油发电机组维修保养_电力/水利_工程科技_专业资料。凸轮盘:146220-... 无锡无动柴油发电机组维... 意大利依维柯柴油发电机... 宁波柴油发电机组维修...
发电机组保养公司具有一批专业维修保养服务人员,在行业内超过十五年的柴油发动机/电气技术工程师,承接各类柴油发电机组 (如康明斯、曼、依维柯、珀金斯、奔驰、三菱、...
柴油发电机维修_机械/仪表_工程科技_专业资料。宁波日兴动力科技有限公司 由于...珀金斯 依维柯 大宇 富豪 三菱 奔驰 卡特 等进口及国产机组特约维修、保养服务。...
世界名牌柴油发电机组对比_电子/电路_工程科技_专业...可靠性高 省却繁琐的维修保养 配有保护装置,确保运作...十三. 依维柯(IVECO)公司 依维柯(IVECO)公司是意大利...
依维柯·爱福 为依维柯公司专为客户生产特种柴油机的公司,位于意大利米兰市,其...维修方面,公司主要成员是具有十多年发电设备维修的专业工程师。有着多年专业维修...
国内柴油发电机组概述_电力/水利_工程科技_专业资料...后通过与欧洲发动机工厂IVECO\VOLVO\SCANIA\等合作,...? PRMAC 意大利知名设备生产商,在欧洲意大利、德国...
热门文档