一;润滑油和煤油的润滑比例是:3:1 2、利用水压法检查汽缸体裂纹,应在 392Mpa 压力下,保持 15 分钟无渗漏 3、柴油机进气门杆部与导管的配合间隙为:0.006——0.107MM 4、柴油机排气门杆部与导管的配合间隙为:0.075——0.127MM 5、柴油机摇臂衬套与摇臂轴的间隙规定为:0.024——0.007MM 6、安装新气门座圈时,为方便装入,可将柴油机缸盖放在机油 中预热至:150——170摄氏度再压入新座圈
12, cylinder liner cavitation of the outer surface of the hole depth within: 3MM liner turned 90 degrees to install Use
13, the detection of the piston ring groove end clearance should be along the circumferential direction of the piston ring groove :3 - 4
Position measurement, where the maximum value for the ring groove face clearance
14, light leakage method check the diesel engine piston and cylinder liner contact with the sealed case, the general rule In entire piston circumferential direction, the light leakage of light leakage at the range shall not be greater than: 30 degrees
15: Diesel engine connecting rod when the bulk of the end cap with the bulk of the joint surface, when the end cap and connecting rod with
Bolt inside diameter dial indicator with the connecting rod shaft axis was: 45 degrees in the direction
On the measurement of two perpendicular diameter size
16, the inspection of the diesel engine connecting rod end caps and the bulk of the joint surface, the tablet so that it Two-plane combination, if the contact surface is not significant gap, is the qualified individual to allow a slight Gap: 0.026 dedicated flakes, but could not get into the gap for qualified
17 in the repair of diesel engine connecting rod hole, start with the combination of two of the connecting rod and rod cap
Surface, the first filing to go :0.2 - 0.3 MM thick metal, and then boring to the standard size
18, the connecting rod alignment, the artificial aging treatment, the specific process,
Rod heated to :400 - 450 degrees, thermal insulation of 0.5 - 1 hour, then slowly
Cooled to room temperature
19,190 range allowed by the size of the connecting rod head hole axis in the vertical direction parallel to the error : 0.03MM
20, when the residual elongation of the connecting rod bolts than the original length: 0.03%
Replaced with new parts
21, the installation of the diesel engine connecting rod, the rod uniformly heated to :180 - 200
Degree, promptly after removing a small head bushing pressure seat hole
22,190 diesel engines require the same diesel engine connecting rod group of poor quality and not more than: 65 grams
23, when measuring the wear of diesel engine crankshaft journal, each journal should be measured to take: two cross sections
Location
24, in the measurement of diesel engine crankshaft journal wear on the location of each cross-section should be measured: 2
Direction
25, the diesel engine crankshaft journal wear and tear can be repaired by grinding, the journal of the largest narrow Should not exceed: 3MM
26, the diesel engine crankshaft journal repair size each: 0.25MM to a group
27, the diesel engine crankshaft journal grinding, repair a hole, it has: 2 * 45 degrees
Chamfer
28, measured with a dial indicator to the diesel engine valve head and valve stem to put the poor, were more than : 0.05 MM and 0.03MM, that the valve rod bending
29,190 series diesel engine intake valve open continuous angle: 300 degrees
30,190 series diesel engine valve overlap angle: 128 degrees
31, oil 50 - 60 degrees, the speed of auto-oxidation was significantly up
32, installation of diesel engine piston pin, should piston is heated to :150 - 170 degrees
33 Overhauling diesel engine piston pin, piston heating should be to :130 - 150 degrees
34, diesel oil ring is installed, the sheets spring opening and the oil ring openings staggered: 180 degrees
南京富电康机电工程有限公司依维柯发电机 依维柯发电机:意大利依维柯公司生产的发电...专业提供依维柯柴油发电 机组的维修 2 提供依维柯柴油发电机组的大修,中修. 3 ...
电气技术工程师,承接各类柴油发 电机组(如康明斯、曼、依维柯、珀金斯、奔驰、三菱、大宇、卡特、电友、日野等)的维修保养业务,能够迅 速准确的诊断发电机组故障并...
新建RTF 格式 (3)依维柯... 2页 免费 意大利依维柯柴油发电机... 8页 ...轮胎的使用与保养 七、行驶系常见故障诊断 一、行驶系的拆卸 1.前悬架的拆卸 ...
柴油发电机组维修日兴动力承接:康明斯 珀金斯 依维柯 大宇 富豪 三菱 奔驰 卡特 强鹿 上柴 潍柴 玉柴等进口及国产机组特约维 修、保养服务。公司可与客户签订长期...
美国科勒柴油发电机组维修保养_电力/水利_工程科技_专业资料。凸轮盘:146220-... 无锡无动柴油发电机组维... 意大利依维柯柴油发电机... 宁波柴油发电机组维修...
发电机组保养公司具有一批专业维修保养服务人员,在行业内超过十五年的柴油发动机/电气技术工程师,承接各类柴油发电机组 (如康明斯、曼、依维柯、珀金斯、奔驰、三菱、...
柴油发电机维修_机械/仪表_工程科技_专业资料。宁波日兴动力科技有限公司 由于...珀金斯 依维柯 大宇 富豪 三菱 奔驰 卡特 等进口及国产机组特约维修、保养服务。...
世界名牌柴油发电机组对比_电子/电路_工程科技_专业...可靠性高 省却繁琐的维修保养 配有保护装置,确保运作...十三. 依维柯(IVECO)公司 依维柯(IVECO)公司是意大利...
依维柯·爱福 为依维柯公司专为客户生产特种柴油机的公司,位于意大利米兰市,其...维修方面,公司主要成员是具有十多年发电设备维修的专业工程师。有着多年专业维修...
国内柴油发电机组概述_电力/水利_工程科技_专业资料...后通过与欧洲发动机工厂IVECO\VOLVO\SCANIA\等合作,...? PRMAC 意大利知名设备生产商,在欧洲意大利、德国...
热门文档