文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 自然科学 > 生物学 > u-blox7-V14_ReceiverDescriptionProtocolSpec_Public
侵权投诉

u-blox7-V14_ReceiverDescriptionProtocolSpec_Public

ublox 软件编程手册

u-blox7-V14_ReceiverDescriptionProtocolSpec_Public

the successful configuration of the port. To validate successful configuration of the TX-ready pin, the portconfiguration should be polled and the settings of TX-ready feature verified (will be set to disabled/all zero ifsettings invalid).

The threshold should not be set above 2 kB, as the internal message buffer limit can be reached before this,resulting in the TX-ready pin never being set as messages are discarded before the threshold is reached.

7.2 Extended TX timeout

If the host does not communicate over SPI or DDC for more than approximately 2 seconds, the device assumesthat the host is no longer using this interface and no more packets are scheduled for this port. This mechanismcan be changed enabling "extended TX timeouts", in which case the receiver delays idling the port until theallocated and undelivered bytes for this port reach 4 kB. This feature is especially useful when using the

TX-ready feature with a message output rate of less than once per second, and polling data only when data isavailable, determined by the TX-ready pin becoming active.

7.3 UART Ports

One or two Universal Asynchronous Receiver/Transmitter () ports are featured, that can be used to

transmit GNSS measurements, monitor status information and configure the receiver. See our online productdescriptions for availability.

The serial ports consist of an RX and a TX line. Neither handshaking signals nor hardware flow control signalsare available. These serial ports operate in asynchronous mode. The baud rates can be configured individuallyfor each serial port. However, there is no support for setting different baud rates for reception and transmissionor for different protocols on the same port.

Possible UART Interface ConfigurationsBaud RateData BitsParityStop Bits

4800

9600

19200

38400

57600

115200888888nonenonenonenonenonenone111111

Note that for protocols such as NMEA or UBX, it does not make sense to change the default word lengthvalues (data bits) since these properties are defined by the protocol and not by the electrical interface.

If the amount of data configured is too much for a certain port's bandwidth (e.g. all UBX messages output on aUART port with a baud rate of 9600), the buffer will fill up. Once the buffer space is exceeded, new messagesto be sent will be dropped. To prevent message losses, the baudrate and communication speed or the numberof enabled messages should be selected so that the expected number of bytes can be transmitted in less thanone second.

See CFG-PRT for UART for a description of the contents of the UART port configuration message.

7.4 USB Port

One Universal Serial Bus () port is featured. See the Data Sheet of your specific product for availability. Thisport can be used for communication purposes and to power the positioning chip or module.

The USB interface supports two different power modes:

In Self Powered Mode the receiver is powered by its own power supply. VDDUSB is used to detect theavailability of the USB port, i.e. whether the receiver is connected to a USB host.

上一页第25页

你可能喜欢

热门文档

相关文档

  • GPS模块协议u-blox5_Protocol_Specifications(GPS.G5-X...

    135 NMEA, UBX Protocol Specification, u-blox 5 GNSS Receiver GPS.G5-X-07036-E Public Release Table of Contents Page ix Receiver Description Overview ...

  • LD420EUB-SDA1_Final

    Receiver Signal (B-) FIRST LVDS Receiver Signal ...V IN _ MAX V IN _ MIN Description LVDS ...9-7. Appropriate Condition for Public Display - ...

  • GWF-7M01_Spec_V10

    4. Product Description 4.1. Block Diagram MT7601 VCC(3.3V) SMPS 3.3V...Receiver RF Front End External antenna 2.412~2.4835GHz LED XTAL 40MHz ...

  • 9-Real_Time_Transport_Protocol

    Source description V=2 P SC PT=SDES=202 SSRC/CSRC 1 SDES items ... ...(s) Receiver Report Receiver Report SSRC SSRC report block(s) 1 report ...

  • ATK-NEO-6M 高性能GPS模块用户手册

    (串口)方式,输出的 GPS 定位数据采用 NMEA-0183 协议(默认) ,控制协议为 UBX 协议(该协议的详细介绍请看 u-blox6_ReceiverDescriptionProtocolSpec_GPS.G6-SW...

  • GPS用户手册_V2.0

    (该协议的详细介绍请看 u-blox6_ReceiverDescriptionProtocolSpec_GPS.G6-SW-...(2) 定位状态,A=有效定位,V=无效定位 (3) 纬度 ddmm.mmmmm(度分) (4)...

  • LD470DXS-SCA1规格书

    PUBLIC DISPLAY ITEM Page 1 2 3 4 5 6 6 8 ...Ground LVDS Receiver Signal(-) LVDS Receiver Signal...V IN _ MAX V IN _ MIN Description LVDS ...

  • LD420WXN-SAA1_Ver_0.0_080129_Pre

    PUBLIC DISPLAY ITEM Page 1 2 3 4 5 6 6 8 ...General Description The LC420WXN is a Color Active...Receiver Clock Signal(-) LVDS Receiver Clock ...

  • L G_LD550DUS-SEB1-低亮高清超窄边

    ‘H’ Description SECOND LVDS Receiver Signal (A...3. (N<M) ※ G to G Spec is average of ...9-7. Appropriate Condition for Public Display - ...

  • YG-309M-A SPEC_V1.1说明书标准书

    Wangcs YG-309M-A DESCRIPTION : CSR8605 (ROM )Module REV : 1.0 CHECKED...LTD Receiver Performance (Temperature 25°C) Issue Date :2013-05-08 17--...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email