文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 自然科学 > 生物学 > u-blox7-V14_ReceiverDescriptionProtocolSpec_Public
侵权投诉

u-blox7-V14_ReceiverDescriptionProtocolSpec_Public

ublox 软件编程手册

u-blox7-V14_ReceiverDescriptionProtocolSpec_Public

In Bus Powered Mode the device is powered by the USB bus, therefore no additional power supply isneeded. See the table below for the default maximum current that can be drawn by the receiver. See

CFG-USB for a description on how to change this maximum. Configuring Bus Powered Mode indicates thatthe device will enter a low power state with disabled GNSS functionality when the host suspends the device,e.g. when the host is put into stand-by mode.

Maximum Current in Bus Powered ModeGeneration

u-blox7-V14_ReceiverDescriptionProtocolSpec_Public

Max Current

u-blox 750 mA

The voltage range for VDDUSB is specified from 3.0V to 3.6V, which differs slightly from thespecification for VCC

7.5 DDC Port

A Display Data Channel () bus is implemented, which is a 2-wire communication interface compatible withthe I²C standard (). See our online product selector matrix for availability.

u-blox7-V14_ReceiverDescriptionProtocolSpec_Public

Unlike all other interfaces, the DDC is not able to communicate in full-duplex mode, i.e. TX and RX are mutuallyexclusive. u-blox receivers act as a slave in the communication setup, therefore they cannot initiate data

transfers on their own. The host, which is always master, provides the data clock (SCL), and the clock frequencyis therefore not configurable on the slave.

The clock rate on the SCL line generated by the master must not exceed 400 kHz (fast-mode).

The receiver's DDC address is set to 0x42 by default. This address can be changed by setting the mode field inCFG-PRT for DDC accordingly.

As the receiver will be run in slave mode and the physical layer lacks a handshake mechanism to inform themaster about data availability, a layer has been inserted between the physical layer and the UBX and NMEAlayer. The DDC implements a simple streaming interface that allows the constant polling of data, discardingeverything that is not parseable. This means that the receiver returns 0xFF if no data is available. The TX-readyfeature can be used to inform the master about data availability and can be used as a trigger for datatransmission.

7.5.1 Read Access

To allow both polled access to the full message stream and quick access to the key data, the register layoutdepicted in Figure DDC Register Layout is provided. The data registers 0 to 252, at addresses 0x00 to 0xFC,

u-blox7-V14_ReceiverDescriptionProtocolSpec_Public

each 1 byte in size, contain information to be defined at a later point in time. At addresses 0xFD and 0xFE, thecurrently available number of bytes in the message stream can be read. At address 0xFF, the message stream islocated. Subsequent reads from 0xFF return the messages in the transmit buffer, byte by byte. If the number ofbytes read exceeds the number of bytes indicated, the payload is padded using the value 0xFF.

The registers 0x00 to 0xFC will be defined in a later firmware release. Do not use them, as they

don't provide any meaningful data!

上一页第26页

你可能喜欢

热门文档

相关文档

  • GPS模块协议u-blox5_Protocol_Specifications(GPS.G5-X...

    135 NMEA, UBX Protocol Specification, u-blox 5 GNSS Receiver GPS.G5-X-07036-E Public Release Table of Contents Page ix Receiver Description Overview ...

  • LD420EUB-SDA1_Final

    Receiver Signal (B-) FIRST LVDS Receiver Signal ...V IN _ MAX V IN _ MIN Description LVDS ...9-7. Appropriate Condition for Public Display - ...

  • GWF-7M01_Spec_V10

    4. Product Description 4.1. Block Diagram MT7601 VCC(3.3V) SMPS 3.3V...Receiver RF Front End External antenna 2.412~2.4835GHz LED XTAL 40MHz ...

  • 9-Real_Time_Transport_Protocol

    Source description V=2 P SC PT=SDES=202 SSRC/CSRC 1 SDES items ... ...(s) Receiver Report Receiver Report SSRC SSRC report block(s) 1 report ...

  • ATK-NEO-6M 高性能GPS模块用户手册

    (串口)方式,输出的 GPS 定位数据采用 NMEA-0183 协议(默认) ,控制协议为 UBX 协议(该协议的详细介绍请看 u-blox6_ReceiverDescriptionProtocolSpec_GPS.G6-SW...

  • GPS用户手册_V2.0

    (该协议的详细介绍请看 u-blox6_ReceiverDescriptionProtocolSpec_GPS.G6-SW-...(2) 定位状态,A=有效定位,V=无效定位 (3) 纬度 ddmm.mmmmm(度分) (4)...

  • LD470DXS-SCA1规格书

    PUBLIC DISPLAY ITEM Page 1 2 3 4 5 6 6 8 ...Ground LVDS Receiver Signal(-) LVDS Receiver Signal...V IN _ MAX V IN _ MIN Description LVDS ...

  • LD420WXN-SAA1_Ver_0.0_080129_Pre

    PUBLIC DISPLAY ITEM Page 1 2 3 4 5 6 6 8 ...General Description The LC420WXN is a Color Active...Receiver Clock Signal(-) LVDS Receiver Clock ...

  • L G_LD550DUS-SEB1-低亮高清超窄边

    ‘H’ Description SECOND LVDS Receiver Signal (A...3. (N<M) ※ G to G Spec is average of ...9-7. Appropriate Condition for Public Display - ...

  • YG-309M-A SPEC_V1.1说明书标准书

    Wangcs YG-309M-A DESCRIPTION : CSR8605 (ROM )Module REV : 1.0 CHECKED...LTD Receiver Performance (Temperature 25°C) Issue Date :2013-05-08 17--...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email