文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 自然科学 > 生物学 > u-blox7-V14_ReceiverDescriptionProtocolSpec_Public
侵权投诉

u-blox7-V14_ReceiverDescriptionProtocolSpec_Public

ublox 软件编程手册

u-blox7-V14_ReceiverDescriptionProtocolSpec_Public

and only then on to 00:00:00.

It is also theoretically possible to have a negative leap second, in which case there will only be 59 seconds in aminute and 23:59:58 will be followed by 00:00:00.

u-blox receivers are designed to handle leap seconds in their UTC output and consequently users processingUTC times from either NMEA and UBX messages should be prepared to handle minutes that are either 59 or 61

u-blox7-V14_ReceiverDescriptionProtocolSpec_Public

seconds long.Note that the behavior of GLONASS signals during leap seconds is not well defined. As a

consequence, users should be prepared for the receiver to restart itself if GLONASS signals are

being tracked when a leap second occurs.

6.6 Real Time Clock

u-blox receivers contain circuitry to support a real time clock, which (if correctly fitted and powered) keepstime while the receiver is otherwise powered off. When the receiver powers up, it attempts to use the real timeclock to initialise receiver local time and in most cases this leads to appreciably faster first fixes.

7 Serial Communication Ports Description

u-blox positioning technology comes with a highly flexible communication interface. It supports the NMEA andthe proprietary UBX protocols, and is truly multi-port and multi-protocol capable. Each protocol (UBX, NMEA)can be assigned to several ports at the same time (multi-port capability) with individual settings (e.g. baud rate,message rates, etc.) for each port. It is even possible to assign more than one protocol (e.g. UBX protocol andNMEA at the same time) to a single port (multi-protocol capability), which is particularly useful for debuggingpurposes.

To enable a message on a port the UBX and/or NMEA protocol must be enabled on that port using the UBXproprietary message CFG-PRT. This message also allows changing port-specific settings (baud rate, addressetc.). See CFG-MSG for a description of the mechanism for enabling and disabling messages.

The following table shows the port numbers used. Note that any numbers not listed are reserved for future use.Port Number assignmentPort #Electrical Interface

1

3

4DDC (I²C compatible)UART 1USBSPI

7.1 TX-ready indication

This feature enables each port to define a corresponding pin, which indicates if bytes are ready to be

transmitted. By default, this feature is disabled. For USB, this feature is configurable but might not behave asdescribed below due to a different internal transmission mechanism. If the number of pending bytes reachesthe threshold configured for this port, the corresponding pin will become active (configurable active-low oractive-high), and stay active until the last bytes have been transferred from software to hardware (note that thisis not necessarily equal to all bytes transmitted, i.e. after the pin has become inactive, up to 16 bytes can stillneed to be transferred to the host).

The TX-ready pin can be selected from all PIOs which are not in use (see MON-HW for a list of the PIOs and theirmapping), each TX-ready pin is exclusively for one port and cannot be shared. If the PIO is invalid or already inuse, only the configuration for the TX-ready pin is ignored, the rest of the port configuration is applied if valid.The acknowledge message does not indicate if the TX-ready configuration is successfully set, it only indicates

上一页第24页

你可能喜欢

热门文档

相关文档

  • GPS模块协议u-blox5_Protocol_Specifications(GPS.G5-X...

    135 NMEA, UBX Protocol Specification, u-blox 5 GNSS Receiver GPS.G5-X-07036-E Public Release Table of Contents Page ix Receiver Description Overview ...

  • LD420EUB-SDA1_Final

    Receiver Signal (B-) FIRST LVDS Receiver Signal ...V IN _ MAX V IN _ MIN Description LVDS ...9-7. Appropriate Condition for Public Display - ...

  • GWF-7M01_Spec_V10

    4. Product Description 4.1. Block Diagram MT7601 VCC(3.3V) SMPS 3.3V...Receiver RF Front End External antenna 2.412~2.4835GHz LED XTAL 40MHz ...

  • 9-Real_Time_Transport_Protocol

    Source description V=2 P SC PT=SDES=202 SSRC/CSRC 1 SDES items ... ...(s) Receiver Report Receiver Report SSRC SSRC report block(s) 1 report ...

  • ATK-NEO-6M 高性能GPS模块用户手册

    (串口)方式,输出的 GPS 定位数据采用 NMEA-0183 协议(默认) ,控制协议为 UBX 协议(该协议的详细介绍请看 u-blox6_ReceiverDescriptionProtocolSpec_GPS.G6-SW...

  • GPS用户手册_V2.0

    (该协议的详细介绍请看 u-blox6_ReceiverDescriptionProtocolSpec_GPS.G6-SW-...(2) 定位状态,A=有效定位,V=无效定位 (3) 纬度 ddmm.mmmmm(度分) (4)...

  • LD470DXS-SCA1规格书

    PUBLIC DISPLAY ITEM Page 1 2 3 4 5 6 6 8 ...Ground LVDS Receiver Signal(-) LVDS Receiver Signal...V IN _ MAX V IN _ MIN Description LVDS ...

  • LD420WXN-SAA1_Ver_0.0_080129_Pre

    PUBLIC DISPLAY ITEM Page 1 2 3 4 5 6 6 8 ...General Description The LC420WXN is a Color Active...Receiver Clock Signal(-) LVDS Receiver Clock ...

  • L G_LD550DUS-SEB1-低亮高清超窄边

    ‘H’ Description SECOND LVDS Receiver Signal (A...3. (N<M) ※ G to G Spec is average of ...9-7. Appropriate Condition for Public Display - ...

  • YG-309M-A SPEC_V1.1说明书标准书

    Wangcs YG-309M-A DESCRIPTION : CSR8605 (ROM )Module REV : 1.0 CHECKED...LTD Receiver Performance (Temperature 25°C) Issue Date :2013-05-08 17--...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email