文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 自然科学 > 生物学 > u-blox7-V14_ReceiverDescriptionProtocolSpec_Public
侵权投诉

u-blox7-V14_ReceiverDescriptionProtocolSpec_Public

ublox 软件编程手册

u-blox7-V14_ReceiverDescriptionProtocolSpec_Public

u-blox7-V14_ReceiverDescriptionProtocolSpec_Public

For maximum GPS coldstart sensitivity, ensure that the SBAS subsystem is enabled.

3.1 GLONASS

GLONASS is a GNSS operated by Russia. It has a number of significant differences when compared to GPS. Inmost cases u-blox receivers operate in a very similar manner when they are configured to use GLONASS signalsinstead of GPS. However some aspects of receiver output are likely to be noticeably affected:

NMEA messages will change to use the GLONASS talker identifier GL (see section NMEA Protocol

Configuration).

UBX messages will report different satellite identity numbers (see section Satellite Numbering).

Positioning accuracy with GLONASS only satellites may be worse than with only GPS satellites. This isbecause of reduced availability; the GLONASS constellation has less satellites (at the time of writing,

nominally 24 for GLONASS instead of 32 for GPS). Additionally, GLONASS signals have a lower chipping ratewhich reduces accuracy.

The identity of GLONASS satellites is determined by decoding specific parts of their data transmission.Therefore newly acquired GLONASS signals may be reported as coming from an "unknown" satellite untilthey are identified. From then on, satellites are reported using the correct satellite identity.

As GLONASS uses a time base aligned directly to UTC, GLONASS receivers are affected by leap seconds,when the UTC time base is occasionally re-calibrated. As a consequence, users should be prepared for the

u-blox7-V14_ReceiverDescriptionProtocolSpec_Public

receiver to restart itself if GLONASS signals are being tracked when a leap second occurs.GPS receivers are unaffected by leap second changes as their time base (GPS time) is independent

of leap seconds. GPS satellites periodically transmit information that allows the receiver to calculate

UTC.

3.2 QZSSQZSS is a GNSS operated by (JAXA). It is intended as an enhancement toGPS which increases availability and positional accuracy. This can be achieved by the QZSS system transmittingGPS-compatible signals in the GPS bands.

NMEA messages will show the QZSS satellites only if configured accordingly (see section Satellite Numbering).4 Satellite Numbering

4.1 NMEA

The NMEA protocol (V2.3) identifies satellites with a two digit number, reserving the numbers 1 to 32 for GPS,33-64 for SBAS and 65-96 for GLONASS. So, for example, GLONASS SV4 is reported using number 68. u-bloxreceivers support this method in their NMEA output when "strict" SV numbering is selected. In most cases thisis the default setting, but can be checked or set using UBX-CFG-NMEA.

Unfortunately there is currently no standard way of identifying satellites from any other GNSS within the NMEAprotocol. In order to support QZSS within current receivers and prepare for support of other systems (e.g.

Galileo) in future receivers, an "extended" SV numbering scheme can be enabled (using UBX-CFG-NMEA). Thisuses the NMEA-defined numbers where possible, but adds other number ranges to support other GNSS. Note

u-blox7-V14_ReceiverDescriptionProtocolSpec_Public

however that these non-standard extensions require 3 digit numbers, which may not be supported by someNMEA parsing software. For example QZSS satellites are reported using numbers in the range 193 to 197.

GLONASS satellites can be tracked before they have been identified. In NMEA output, such

上一页第17页

你可能喜欢

热门文档

相关文档

  • GPS模块协议u-blox5_Protocol_Specifications(GPS.G5-X...

    135 NMEA, UBX Protocol Specification, u-blox 5 GNSS Receiver GPS.G5-X-07036-E Public Release Table of Contents Page ix Receiver Description Overview ...

  • LD420EUB-SDA1_Final

    Receiver Signal (B-) FIRST LVDS Receiver Signal ...V IN _ MAX V IN _ MIN Description LVDS ...9-7. Appropriate Condition for Public Display - ...

  • GWF-7M01_Spec_V10

    4. Product Description 4.1. Block Diagram MT7601 VCC(3.3V) SMPS 3.3V...Receiver RF Front End External antenna 2.412~2.4835GHz LED XTAL 40MHz ...

  • 9-Real_Time_Transport_Protocol

    Source description V=2 P SC PT=SDES=202 SSRC/CSRC 1 SDES items ... ...(s) Receiver Report Receiver Report SSRC SSRC report block(s) 1 report ...

  • ATK-NEO-6M 高性能GPS模块用户手册

    (串口)方式,输出的 GPS 定位数据采用 NMEA-0183 协议(默认) ,控制协议为 UBX 协议(该协议的详细介绍请看 u-blox6_ReceiverDescriptionProtocolSpec_GPS.G6-SW...

  • GPS用户手册_V2.0

    (该协议的详细介绍请看 u-blox6_ReceiverDescriptionProtocolSpec_GPS.G6-SW-...(2) 定位状态,A=有效定位,V=无效定位 (3) 纬度 ddmm.mmmmm(度分) (4)...

  • LD470DXS-SCA1规格书

    PUBLIC DISPLAY ITEM Page 1 2 3 4 5 6 6 8 ...Ground LVDS Receiver Signal(-) LVDS Receiver Signal...V IN _ MAX V IN _ MIN Description LVDS ...

  • LD420WXN-SAA1_Ver_0.0_080129_Pre

    PUBLIC DISPLAY ITEM Page 1 2 3 4 5 6 6 8 ...General Description The LC420WXN is a Color Active...Receiver Clock Signal(-) LVDS Receiver Clock ...

  • L G_LD550DUS-SEB1-低亮高清超窄边

    ‘H’ Description SECOND LVDS Receiver Signal (A...3. (N<M) ※ G to G Spec is average of ...9-7. Appropriate Condition for Public Display - ...

  • YG-309M-A SPEC_V1.1说明书标准书

    Wangcs YG-309M-A DESCRIPTION : CSR8605 (ROM )Module REV : 1.0 CHECKED...LTD Receiver Performance (Temperature 25°C) Issue Date :2013-05-08 17--...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email