文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 自然科学 > 生物学 > u-blox7-V14_ReceiverDescriptionProtocolSpec_Public
侵权投诉

u-blox7-V14_ReceiverDescriptionProtocolSpec_Public

ublox 软件编程手册

u-blox7-V14_ReceiverDescriptionProtocolSpec_Public

and users are recommended to use the UBX-NAV-PVT message in preference.

The UBX-CFG-NAV5 message also defines TDOP and time accuracy values that are used in order to establishwhether a fix is regarded as locked to GNSS or not and, as a consequence of this, which time pulse setting hasto be used. Fixes that do not meet both criteria will be regarded as unlocked to GNSS and the correspondingtime pulse settings of UBX-CFG-TP5 will be used to generate a time pulse.

2.4 Static Hold

Static Hold Mode allows the navigation algorithms to decrease the noise in the position output when thevelocity is below a pre-defined ‘Static Hold Threshold’. This reduces the position wander caused by

environmental factors such as multi-path and improves position accuracy especially in stationary applications.By default, static hold mode is disabled.

If the speed drops below the defined ‘Static Hold Threshold’, the Static Hold Mode will be activated. Once

Static Hold Mode has been entered, the position output is kept static and the velocity is set to zero until there isevidence of movement again. Such evidence can be velocity, acceleration, changes of the valid flag (e.g.position accuracy estimate exceeding the Position Accuracy Mask, see also section Navigation Output Filters),position displacement, etc.

2.5 Freezing the Course Over Ground

The receiver derives the course over ground from the GNSS velocity information. If the velocity cannot becalculated with sufficient accuracy (e.g., with bad signals) or if the absolute speed value is very low (under 0.1m/s) then the course over ground value becomes inaccurate too. In this case the course over ground value isfrozen, i.e. the previous value is kept and its accuracy is degraded over time. These frozen values will not beoutput in the NMEA messages NMEA-RMC and NMEA-VTG unless the NMEA protocol is explicitely configuredto do so (see NMEA Protocol Configuration).

2.6 Degraded Navigation

Degraded navigation describes all navigation modes which use less than 4 Satellite Vehicles (SVs).

2.6.1 2D Navigation

If the receiver only has 3 SVs for calculating a position, the navigation algorithm uses a constant altitude tocompensate for the missing fourth SV. When an SV is lost after a successful 3D fix (min. 4 SVs available), the

u-blox7-V14_ReceiverDescriptionProtocolSpec_Public

altitude is kept constant at the last known value. This is called a 2D fix.u-blox positioning technology does not calculate any solution with less than 3 SVs. Only u-blox

timing receivers can, when stationary, calculate a timing solution with only 1 SV.

3 GNSS Configuration

The latest products from u-blox are multi-GNSS receivers capable of receiving and processing signals frommultiple Global Navigation Satellite Systems (GNSS).

u-blox multi-GNSS receivers can acquire and track satellites from multiple GNSS systems and utilize them inpositioning. u-blox multi-GNSS receivers can be configured to process either:

GPS, SBAS (e.g. WAAS, EGNOS, MSAS) and QZSS L1 signals, centred on 1575.42MHz L1 frequency GLONASS L1 signals, centred on 1602.00MHz L1 frequency

Use the UBX-CFG-GNSS message to configure the u-blox receiver into the required mode of operation. Thismessage allows the user to specify which GNSS signals should be processed along with limits on how manytracking channels should be allocated to each GNSS. The receiver will respond to such a request with a

上一页第16页

你可能喜欢

热门文档

相关文档

  • GPS模块协议u-blox5_Protocol_Specifications(GPS.G5-X...

    135 NMEA, UBX Protocol Specification, u-blox 5 GNSS Receiver GPS.G5-X-07036-E Public Release Table of Contents Page ix Receiver Description Overview ...

  • LD420EUB-SDA1_Final

    Receiver Signal (B-) FIRST LVDS Receiver Signal ...V IN _ MAX V IN _ MIN Description LVDS ...9-7. Appropriate Condition for Public Display - ...

  • GWF-7M01_Spec_V10

    4. Product Description 4.1. Block Diagram MT7601 VCC(3.3V) SMPS 3.3V...Receiver RF Front End External antenna 2.412~2.4835GHz LED XTAL 40MHz ...

  • 9-Real_Time_Transport_Protocol

    Source description V=2 P SC PT=SDES=202 SSRC/CSRC 1 SDES items ... ...(s) Receiver Report Receiver Report SSRC SSRC report block(s) 1 report ...

  • ATK-NEO-6M 高性能GPS模块用户手册

    (串口)方式,输出的 GPS 定位数据采用 NMEA-0183 协议(默认) ,控制协议为 UBX 协议(该协议的详细介绍请看 u-blox6_ReceiverDescriptionProtocolSpec_GPS.G6-SW...

  • GPS用户手册_V2.0

    (该协议的详细介绍请看 u-blox6_ReceiverDescriptionProtocolSpec_GPS.G6-SW-...(2) 定位状态,A=有效定位,V=无效定位 (3) 纬度 ddmm.mmmmm(度分) (4)...

  • LD470DXS-SCA1规格书

    PUBLIC DISPLAY ITEM Page 1 2 3 4 5 6 6 8 ...Ground LVDS Receiver Signal(-) LVDS Receiver Signal...V IN _ MAX V IN _ MIN Description LVDS ...

  • LD420WXN-SAA1_Ver_0.0_080129_Pre

    PUBLIC DISPLAY ITEM Page 1 2 3 4 5 6 6 8 ...General Description The LC420WXN is a Color Active...Receiver Clock Signal(-) LVDS Receiver Clock ...

  • L G_LD550DUS-SEB1-低亮高清超窄边

    ‘H’ Description SECOND LVDS Receiver Signal (A...3. (N<M) ※ G to G Spec is average of ...9-7. Appropriate Condition for Public Display - ...

  • YG-309M-A SPEC_V1.1说明书标准书

    Wangcs YG-309M-A DESCRIPTION : CSR8605 (ROM )Module REV : 1.0 CHECKED...LTD Receiver Performance (Temperature 25°C) Issue Date :2013-05-08 17--...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email