文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 电力/水利 > PLC的抗干扰研究
侵权投诉

PLC的抗干扰研究

Yuefan Liu et al. / Procedia Engineering 15 (2011) 1673 – 16771675interference and common mode interference of two. Differential mode interference is superimposed on the measured signal interference signal line, such interference is mostly high frequency of the alternating signal, the source is usually coupled interference. Normal interference suppression methods are: RC filter connected in the input loop or double T filter; maximize the use of double integral type A / D converter, since the characteristics of such integrator, has some role to eliminate high frequency interference; the voltage signals into current signals re-transmitted. Common mode interference is the interference signal line there, typically by the end of the measured signal and ground terminals and ground control system there is a certain potential difference caused by this interference in the two signal line period, amplitude almost the same situation, using the above methods can not eliminate or suppress. Solution as follows: dual differential input differential amplifier, which amplifier has a high common mode rejection ratio; input line using stranded wire, stranded wire can reduce common mode interference, the sensor offset each other; using optical isolation method can eliminate the common mode interference; use shielded cable and the unilateral ground; in order to avoid signal distortion, the signal for long distance transmission should pay attention to impedance matching. In addition, the software measures can be taken. To improve the input signal to noise ratio, software digital filtering are used to improve the useful signal authenticity. For large random interference system, using procedures limiting law, that continuous sampling 5 times, if a sample of a sample support is much larger than the amplitude of the other several times, then take care of. For the flow, pressure, liquid level, displacement and other parameters are frequent fluctuations in a certain range, then the arithmetic average. Samples with n time the average instead of the current value. General view: Flow n = 12, stress n = 4 the most appropriate.

2.3.Disturbance from the ground system disorder

The purpose of grounding usually have two, one for security, the other is to suppress interference. Complete PLC control system grounding system is an important measure against one of electromagnetic interference. Ground is to improve the electromagnetic compatibility of electronic equipment (EMC) is one effective means. Properly grounded, can not only inhibit the impact of electromagnetic interference, but also outgoing interference suppression equipment; and the wrong ground, it will introduce serious interference signal to PLC system will not work correctly. PLC control system, including ground systems, the shield and the exchange of land and protect the land. Confusion on the PLC system, grounding system interference is primarily a place of potential uneven distribution of access, the existence of different ground point to the potential difference between, causing ground loop currents, affecting the system work properly. For example, cable shield must be grounded point. If the cable shields at both ends A, B are grounded, there is ground potential difference, a current flows through the shield, when the abnormal state, such as lightning, the ground current will be greater. Grounding design has two principles: elimination of the circuit current by a public ground noise voltage generated by impedance. To avoid the formation of ground loop, in order to suppress additional power supply and input, output interference, should be connected to the PLC-specific ground, and then place points with other devices. Systems grounding are: floating mode, the direct grounding and grounded capacitors three ways. On the PLC control systems, it is a high-speed low-level control devices, should direct grounding. As the signal cable distribution installation input filtering capacitor and the impact of the exchange frequency of the signal between the devices are generally less than 1MHz, so grounding line PLC control system in series with a little bit ground and grounding. Layout of the PLC system is suitable for centralized parallel grounding point, the device enclosure center ground point to a separate ground wire grounding lead. If the device spacing larger point grounding should be used in series. Copper bus bar with a large cross section

上一页第3页

你可能喜欢

热门文档

相关文档

  • 【论文】PLC系统设计及抗干扰研究

    PLC系统设计及抗干扰研究_专业资料。随着PLC在自动化控制领域的普及,提高PLC控制系统的抗干扰能力显得十分重要。介绍了PLC的设计原则,并从硬件和软件的角度提出了抗...

  • 【论文】PLC控制系统的抗干扰研究

    PLC控制系统的抗干扰研究_专业资料。文章分析了工业现场的干扰来源,指出了抑制干扰措施在实际工程应用中的重要地位,有针对性地设计了PLC控制系统的硬件与软件抗干扰...

  • PLC控制系统的抗干扰研究

    PLC控制系统的抗干扰研究PLC控制系统的抗干扰研究隐藏>> PLC 控制系统的抗干扰研究 1 概述 PLC 作为一种自动化程度高、配置灵活的工业生产过程控制装置,因为其...

  • PLC系统抗干扰的研究

    PLC系统抗干扰的研究 着重介绍了PLC系统的组成、内部抗干扰措施以及在应用中的抗干扰方案。着重介绍了PLC系统的组成、内部抗干扰措施以及在应用中的抗干扰方案。...

  • PLC控制系统的抗干扰问题研究

    PLC控制系统的抗干扰问题研究PLC控制系统的抗干扰问题研究隐藏>> 维普资讯 http://www.cqvip.com 科之 学友 Fnfieme rde ari cctseonAuS 27 9囝 0~0l0,E P...

  • PLC控制系统的抗干扰研究

    7 ? PLC 控制系统的抗干扰研究熊幸明 ( 长沙大学电子系 ,湖南长沙 410003) [ 摘 要] 文中对影响 PLC 控制系统稳定性的主要干扰源 、 成因进行了分析 。从...

  • PLC抗干扰

    PLC抗干扰_信息与通信_工程科技_专业资料。PLC抗干扰PI.jC控制系统的 电源抗干扰问题研究李萍浙江水利水电专科学校机电系310018 使用隔离变压器加以隔离。这是由于...

  • 【论文】PLC系统中的抗干扰问题研究

    PLC系统中的抗干扰问题研究_自然科学_专业资料 暂无评价

  • PLC系统应用中抗干扰问题分析

    PLC系统应用中抗干扰问题分析_机械/仪表_工程科技_专业资料。PLC 系统应用中的抗干扰问题分析 【摘要】随着科学技术的发展,计算机技术的不断进步,出现 了很多有...

  • PLC控制系统抗干扰技术研究

    PLC控制系统抗干扰技术研究 阐述了PLC控制系统存在的主要干扰源,针对干扰源的不同途径,从硬件和软件两方面,阐述了电源抗干扰设计措施、输入输出电路抗干扰设计措施,...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email