1676 Yuefan Liu et al. / Procedia Engineering 15 (2011) 1673 – 1677

(or insulated cable) connections for each unit of the Cabinet are picked up by location, and then directly connected to ground bus grounding. Grounding wire with cross section greater than 22mm2 copper wires, the total bus use of the copper cross section is larger than 60mm2. Grounding of the grounding resistance of less than 2 , buried in the ground very best 10 ~ 15m away from the building, and the PLC system must take place take place with the strong electrical equipment more than 10m apart. Should try to avoid strong grounding wire electrical circuit and main circuit wires, can not be vertical to avoid the intersection, running flat length as short as possible. Source grounded, the signal side of the shield should be grounded; no ground should be grounded in the PLC side; signal the middle connector, the shielding layer and the insulation should be firmly attached to the handle, multi-point ground must be avoided; multiple test point signals and multi-core twisted pair shielded twisted pair shielded cable connection, the shield should be connected with each other, and insulated handle. Select the appropriate single-point grounding Department contacts.
Shielding ground
Fig.1 Single point grounding
2.4.Interference from the inverter
There are two Interference from the inverter: First, start and run the inverter harmonics generated in the process conducted interference generated on the grid, causing power grid voltage distortion, affecting the quality of power supply; Secondly, the inverter output will produce more strong electromagnetic radiation interference, affect the normal operation of peripheral equipment. Interference is too much trouble dealing with the inverter, generally have the following categories:
Isolation transformer It mainly directed against conducted interference from the power supply. It can block most of the conducted interference prior to the isolation transformer. Also transform the role of both supply voltage. Tilter Two kinds of active and passive filter points generally use the passive filter that will have effect. These filters have strong anti-dry. Interference ability of the device itself also has to prevent transmission to the power of interference, and some absorption in both the peak voltage.
Output Reactor
PLC系统设计及抗干扰研究_专业资料。随着PLC在自动化控制领域的普及,提高PLC控制系统的抗干扰能力显得十分重要。介绍了PLC的设计原则,并从硬件和软件的角度提出了抗...
PLC控制系统的抗干扰研究_专业资料。文章分析了工业现场的干扰来源,指出了抑制干扰措施在实际工程应用中的重要地位,有针对性地设计了PLC控制系统的硬件与软件抗干扰...
PLC控制系统的抗干扰研究PLC控制系统的抗干扰研究隐藏>> PLC 控制系统的抗干扰研究 1 概述 PLC 作为一种自动化程度高、配置灵活的工业生产过程控制装置,因为其...
PLC系统抗干扰的研究 着重介绍了PLC系统的组成、内部抗干扰措施以及在应用中的抗干扰方案。着重介绍了PLC系统的组成、内部抗干扰措施以及在应用中的抗干扰方案。...
PLC控制系统的抗干扰问题研究PLC控制系统的抗干扰问题研究隐藏>> 维普资讯 http://www.cqvip.com 科之 学友 Fnfieme rde ari cctseonAuS 27 9囝 0~0l0,E P...
7 ? PLC 控制系统的抗干扰研究熊幸明 ( 长沙大学电子系 ,湖南长沙 410003) [ 摘 要] 文中对影响 PLC 控制系统稳定性的主要干扰源 、 成因进行了分析 。从...
PLC抗干扰_信息与通信_工程科技_专业资料。PLC抗干扰PI.jC控制系统的 电源抗干扰问题研究李萍浙江水利水电专科学校机电系310018 使用隔离变压器加以隔离。这是由于...
PLC系统中的抗干扰问题研究_自然科学_专业资料 暂无评价
PLC系统应用中抗干扰问题分析_机械/仪表_工程科技_专业资料。PLC 系统应用中的抗干扰问题分析 【摘要】随着科学技术的发展,计算机技术的不断进步,出现 了很多有...
PLC控制系统抗干扰技术研究 阐述了PLC控制系统存在的主要干扰源,针对干扰源的不同途径,从硬件和软件两方面,阐述了电源抗干扰设计措施、输入输出电路抗干扰设计措施,...
热门文档