


Fig. 2 Cross-sectional view of the VIP coupler model (a) parameter definition, (b) odd mode, (c) even mode.
The broadside coupler implemented in the VIP corresponds to the coupled lines section in Fig. 1(a). The backside of the horizontal PCB is a full metal ground. The high impedance transmission line is implemented on the horizontal PCB. The overall length of the transmission line is equal to a quarter wavelength at the center frequency. Fig. 3 HFSS simulation result of Z0o and Z0e for different H and This circuit is able to transform the impedance from Z1 to Z2. W (substrate: RO4003, t =t = 32 mil). 1 2 The input transmission line with characteristic impedance Z 1 and the output transmission line with characteristic impedance Z2 are printed on the horizontal PCB. The vertical PCB is connected to the horizontal PCB through soldering joints.
III. CHARACTERISTIC OF VIP COUPLER
The design curves given in [4] are used to determine Z0o and Z0e and Z0 values needed to obtain the desired impedance transformation ratio Z2/Z1 and the bandwidth required. To link these values with the physical dimensions of the VIP coupler, parametric studies of the VIP coupler are conducted using Ansoft HFSS. The odd mode impedance Z0o is primarily controlled by the width (W) of the trace, the dielectric constant and the thickness of the vertical PCB [5], [6]. The even mode impedance, Z0e, is mainly determined by the height H of the trace from the horizontal PCB [5], [6]. Fig. 2(a) shows the cross sectional view and the parameters used for the parametric study in HFSS. The coupling coefficients of the VIP coupler can be controlled by varying these parameters. Fig. 2(b) and 2(c) illustrate the Fig. 4 HFSS simulation of the even mode and odd mode models for the simulation of the even mode and odd mode effective dielectric constants. impedance, Z0e and Z0o. The electric field is mainly confined
Fig. 3 shows the achievable Z and Z for different in the vertical substrate for odd mode excitation and the 0e 0o
electric field is mainly confined in air and the horizontal values of H and W. The effective dielectric constants for the
even mode and odd mode are shown in Fig. 4. The odd substrate for even mode excitation.
reduced by increasing the width While the thickness and dielectric constants of the mode impedance can be
(W) of the coupled lines. The even mode impedance can be
substrates (t1, t2 and r1, r2) also affect Z 0e and Z 0o, the choice
increased by increasing the height H. From the figures, it
may be limited due to considerations such as cost and can be seen that the VIP coupler allows designers to rigidity of the substrate. Therefore, the parametric study overcome the fabrication limitations of the traditional planar focuses on the width of the coupled lines (W) and the height implementation. Based on these curves, the dimensions of of the coupled lines from the horizontal substrate (H). The W and H of the coupler can be determined for any given material used is RO4003 with a thickness of 32 mil. combination of Z0o and Z0e.
The conventional quarter-wavelength impedance transformer is easy to implement ...A compact broadband impedance transformer with three reflection zeros was ...
. Case 1: a quarter-wavelength transformer of impedance of 31.6 ? , ...-10 dB 30 to 70 degrees Qingyuan Wang, “Broadband microstrip circuits, ...
Unit 4:Resonant Modes, Bilinear Transformation between Impedance and Reflection... ) 11 Quarter-wavelength Transformer lg 4 Z0 Zg Z0 d1 ZL d1 = l ...
A broadband series power divider using zero-degree metamaterial phase-...quarter-wavelength transformers were added to provide a broadband impedance ...
4 Broadband selected to give a maximally flat response.6 These transitions ...Each transformer contains three one-quarter-wavelength steps with impedance ...
5-1 CHAPTER 5 Impedance Matching and Smith Chart...(such as broadband design) - adjustability - ...Chuang EE NCKU 5-23 ??Quarter-Wave Transformer ...
Resistive feedback and transformer matching network are proposed in this PA design to enhance the broadband frequency response. The broadband load impedance ...
(narrow band techniques) or for a given frequency spectrum (broadband ...The quarter-wavelength transformer provides narrow-band impedance matching. The...
Harmonic Suppression in Broadband Microstrip Patch ...quarter-wavelength transformer feeding as well as ...However, their large input impedance at the ...
Broadband circularly pol... 暂无评价 4页 2财富值 08_Fractal boundary ... and a quarter-wavelength impedance transformer is used to overcome the ...
热门文档