



Fig. 5 Simulated response of the impedance transformer.
Fig. 7 Measured |S11| and |S21| (solid line) and simulated |S11| and
|S21| (dotted line).
Fig. 6 Fabricated quarter-wavelength impedance transformer.
IV. THE IMPEDANCE TRANSFORMER SIMULATION To demonstrate the usefulness of the design curves and
the merit of using the VIP coupler, an impedance transformer from 50 to 100 was designed for a frequency range of 0.8 GHz to 2.2 GHz, with the centre frequency at 1.5 GHz. The bandwidth is 93%. The design bandwidth and transformation ratio are chosen such that the required Z0 is not too high to be realized. The required Z0 = 135 , Z0e = 158 and Z0o = 44 . For the case where both substrates are RO4003 with a thickness of 32 mil and a dielectric constant of 3.55, the physical dimensions of the VIP coupler can be determined from Fig. 3. The required values are H = 0.2 mm and W = 1.2 mm. The even mode and odd mode effective dielectric constants are 1.95 and 2.85 respectively.
To confirm the design, an Ansoft HFSS model of the full transformer is generated and simulated. Fig. 5 shows the simulated |S11| and |S21| response. Only two nulls in the return loss response are observed. The potential reason may be due to the inaccurate electrical length of the high impedance transmission line.
Fig. 8 Measured |S12|and |S22| (solid line) and simulated |S12| and
|S22| (dotted line)
As the high impedance transmission line is partly on the horizontal PCB and partly on the vertical PCB, accurate determination of the overall electrical length is a challenge. Optimization is required to further improve the design. The return loss is below 18 dB from 0.7 GHz to 1.75 GHz and below 12 dB from 1.75 GHz to 2 GHz. A frequency shift to the lower side of the designed frequency band is observed.
V. MEASUREMENT AND DISCUSSION
The impedance transformer was fabricated and measured for further comparison. Fig. 6 shows the photo of the fabricated circuit. Besides the required traces, soldering pads are also included in the design. The two PCBs are soldered together to maintain the relative position and connectivity.
The conventional quarter-wavelength impedance transformer is easy to implement ...A compact broadband impedance transformer with three reflection zeros was ...
. Case 1: a quarter-wavelength transformer of impedance of 31.6 ? , ...-10 dB 30 to 70 degrees Qingyuan Wang, “Broadband microstrip circuits, ...
Unit 4:Resonant Modes, Bilinear Transformation between Impedance and Reflection... ) 11 Quarter-wavelength Transformer lg 4 Z0 Zg Z0 d1 ZL d1 = l ...
A broadband series power divider using zero-degree metamaterial phase-...quarter-wavelength transformers were added to provide a broadband impedance ...
4 Broadband selected to give a maximally flat response.6 These transitions ...Each transformer contains three one-quarter-wavelength steps with impedance ...
5-1 CHAPTER 5 Impedance Matching and Smith Chart...(such as broadband design) - adjustability - ...Chuang EE NCKU 5-23 ??Quarter-Wave Transformer ...
Resistive feedback and transformer matching network are proposed in this PA design to enhance the broadband frequency response. The broadband load impedance ...
(narrow band techniques) or for a given frequency spectrum (broadband ...The quarter-wavelength transformer provides narrow-band impedance matching. The...
Harmonic Suppression in Broadband Microstrip Patch ...quarter-wavelength transformer feeding as well as ...However, their large input impedance at the ...
Broadband circularly pol... 暂无评价 4页 2财富值 08_Fractal boundary ... and a quarter-wavelength impedance transformer is used to overcome the ...
热门文档