3 FINITE ELEMENT BACK-ANALYSIS
Figure 5 illustrates the mesh model that was used in a typical Finite Element Analysis. The 15-node ele-ment triangular element type with 12 gaussian points suitable for stress and collapse calculation was used. However the used of such elements leads to relatively higher memory consumption. For Phi-c type of analysis in Plaxis Version 8 the 15-node elements is technically better for Factor-of-safety calculations.
An advance double stiffness soil model known as Hardening Soil (HS) model was used in the analysis and the full explanation and derivation of this model can be obtain in Schanz (1999) and Brinkgreve (2000). The soil parameters adopted in the investigation was based on the available data derived from field investigation as well as from Rahardjo (2001). In contrast to an elastic perfectly-plastic model, the yield surface of the HS model is not fixed in principal stress space, but will expand due to plastic straining. When subjected to primary deviator loading, soil shows a decreasing stiffness and irreversible plastic strains develop. Kondner (1963) formulated hyperbolic equations to represent observed stress-strain relationships in the laboratory and later used in the well-known hyperbolic model by Duncan and Chang (1970). The HS Model is by far more supe-rior than the hyperbolic model as the theory of plasticity was adopted rather then the theory of elasticity. Sec-ondly, by including soil dilatancy and thirdly, by introducing a yield cap. Figure 6 and Table 1 illustrates the HS model. The simple Mohr-Coulomb was also used during the preparation of finite element test models. Ta-ble 2 showed the HS parameters obtained for the 3 soil layers used in the slope analysis.
The ‘smeared’ soil nail technique was used to transform the discrete nails into equivalent plates. Figure 7 il-lustrates briefly the concept of equivalent plate approach. The soil nail inclusions were modeled using beam elements with three degrees of freedom per node (ux uy φz). When 15-node triangular continuum element are used, 5-node beam elements will be employed in the finite element code (Please see Figure 8). The beam ele-ments are based on Mindlin’s beam theory. This theory allows for beam deflections due to shearing as well as bending and in addition, the element can change length when axial force is applied.
The 10 node interface element is used to model the stick-slip interaction between soil and nail inclusion. Five Newton Cotes stress points are located between the node pairs. The stick-slip condition is govern by the Moh-Coulomb failure criteria and R interaction factor. The shearing strength and stiffness (Pullout strength and deformation) of interface elements were deduced from field pullout tests. Figure 9 illustrates the shear stiffness that was used in the analyses.
4 FINITE ELEMENT RESULTS
Sensitivity runs were made to gauge the effect of soil strength parameters on the deformation of the slope and maximum tensile force of soil nails, however these results will not be presented here. The quality of pre-diction after post construction is presented in Figures 10 and 11.
The predicted axial force along soil nail 1 and 2 is given Figure 10 and are compared to the measured read-ings. The general trend of axial force mobilization along the soil nail is not precisely predicted but it is quite close to the measured behavior. The predicted maximum axial force for soil nail 1 is similar and the position of maximum tensile force is similar too. However for soil nail 2 the predicted trend is dissimilar. The predicted tensile force is less then the measured value and the predicted location of maximum tensile force is again dis-similar to the measured value.










Finite Element Analysis ... 10页 免费 ... Analysis of soil nailed earth slope by discrete...some degree of accuracy, and local safety factors...
Analysis of soil nailed ... 14页 免费 (贾永辉)Finite element a... ...χ in Bishop’s strength equation can be obtained according to experience, ...
Soil fungistasis and i... 暂无评价 7页 2.00 A case study on the me... 暂无评价 9页 免费 Eyeful-Case Study-Lain... 4页 1下载券 A Case...
Finite element analysis grid chart 本文把按照以上...soil nailed wall 为了分析土钉墙支护极限高度的影响...soil and horizontal displacement of toe of slope ...
Soil fungistasis and i... 暂无评价 7页 2.00 A case study on the me... 暂无评价 9页 免费 Eyeful-Case Study-Lain... 4页 1下载券 A Case...
热门文档