计算机网络
1、改寄存值
2、把NVRAM中的配置文件COPY到RAM
3、更改相应密码等信息
4、将寄存值改回正常值
5、保存
R1#
R1#
R1#en
R1#cohf t
^
% Invalid input detected at '^' marker.
R1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#
R1(config)#
R1(config)#
R1(config)#ena
R1(config)#enable se
R1(config)#enable secret asdhiqw dhiqwhdiuqfhqw
R1(config)#
R1(config)#
R1(config)#
R1(config)#
R1(config)#exit
R1#
%SYS-5-CONFIG_I: Configured from console by console
R1#exit
R1 con0 is now available
Press RETURN to get started.
R1>
R1>
R1>
R1>
R1>
R1>
R1>
R1>
R1>System Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1)
Copyright (c) 2000 by cisco Systems, Inc.
cisco 2621 (MPC860) processor (revision 0x200) with 60416K/5120K bytes of memory
Self decompressing the image :
########################
monitor: command "boot" aborted due to user interrupt
rommon 1 > ?
boot boot up an external process
confreg configuration register utility
dir list files in file system
help monitor builtin command help
reset system reset
set display the monitor variables
tftpdnld tftp image download
unset unset a monitor variable
rommon 2 > confreg 0x2142
rommon 3 >
rommon 3 >
rommon 3 >
rommon 3 > reset
System Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1)
Copyright (c) 2000 by cisco Systems, Inc.
cisco 2621 (MPC860) processor (revision 0x200) with 60416K/5120K bytes of memory
Self decompressing the image :
########################################################################## [OK]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-I-M), Version 12.2(28), RELEASE SOFTWARE (fc5)
Technical Support: doc.guandang.net
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Wed 27-Apr-04 19:01 by miwang
cisco 2621 (MPC860) processor (revision 0x200) with 60416K/5120K bytes of memory
.
Processor board ID JAD05190MTZ (4292891495)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
4 FastEthernet/IEEE 802.3 interface(s)
4 Low-speed serial(sync/async) network interface(s)
32K bytes of non-volatile configuration memory.
63488K bytes of ATA CompactFlash (Read/Write)
--- System Configuration Dialog ---
路由器密码恢复_IT/计算机_专业资料。路由器密码恢复一、 路由器密码恢复 按照以下步骤恢复路由器密码: 1. 关闭路由器的电源并在10秒后重新给路由器加电,在给路...
密码恢复 路由器的密码恢复是将路由器重启、中断再进入ROM监控模式,将设备设置为忽略配置文件,然后再重启,退出初始配置对话模式,配置存储器,然后读出或重新设置密码...
路由器密码恢复_IT/计算机_专业资料。cisco路由器密码恢复如果忘记了路由器的enable密码,就不能对路由器进行配置,想要重新配置路由器必须使路由器再启动时绕过Startup...
路由器密码恢复恢复为出厂默认设置,请参考如下步骤: 1. 断开路由器电源。 2. 按下 RESET 按钮不放或者用牙签按住路由器后面的小孔(复位键)不放。 3. 重新插...
密码恢复关闭路由器电源并重新开机,当控制台出现路由器的启动过程时,赶快按【Ctrl+C】键 (真实设备中按【Ctrl+Break】 )中断路由器的启动,进入 rommon 模式。 ...
路由器密码恢复_计算机硬件及网络_IT/计算机_专业资料。路由器的密码恢复在前面我说了, 只要在 cisco 网络设备启动后, 不让它加载 startup-config 文件就可以了。...
Cisco 路由器的 enable 密码恢复(适用 1700/2600/3600/3700) 1、 连接路由器 将装有超级终端软件的 PC 接到路由器的 console 口上。终端参数设置如下: 速率: ...
路由器 IOS 与配置文件的备份、恢复实验目的:掌握 IOS 备份、升级及配置文件的备份、恢复 实验设备:C3640 一台 软件需求:Cisco TFTP Server 实验过程: 两边先配...
39页 免费 Cisco路由器密码恢复 10页 2财富值搜你所想,读你所爱 拒绝盗版,营造绿色文库 如要投诉违规内容,请到百度文库投诉中心;如要提出功能问题或意见建议,...
华为路由器密码恢复中低端路由器清除密码方法 清除 BOOTROM 密码: 中低端路由器的 BOOTROM 缺省是没有的 , 若设置后丢失 , 只能使用万能密码:WhiteLily2970013 ...
热门文档