文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 机械/仪表 > AMS 2759-9D-2009 钢制零件的除氢
侵权投诉

AMS 2759-9D-2009 钢制零件的除氢

原文

3.4.4 3.4.5

Date and time of completion of baking. Furnace control instrument set temperature.

3.4.6 Furnace identification.

4. QUALITY ASSURANCE PROVISIONS 4.1 Reports

Processor’s reports shall include the baking time and temperature and shall state that baking was performed in accordance with AMS2759/9D.

4.2 Records shall be retained for at least 5 years, including all information required in 3.5, and shall be available for

review by authorized representatives of purchaser. 5. PREPARATION FOR DELIVERY In accordance with AMS2759. 6. ACKNOWLEDGMENT In accordance with AMS2759. 7. REJECTIONS

In accordance with AMS2759. 8. NOTES

8.1 A change bar (l) located in the left margin is for the convenience of the user in locating areas where technical

revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. 8.2

Ordering Data

In order to ensure that the appropriate baking treatment is applied to each lot of parts, it is essential that the processor be furnished with information identifying the material and its minimum strength or hardness or, in the case of precipitation hardening stainless steel, its temper. Additionally, the tempering temperatures should be furnished to the processor for carburized or carbonitrided parts and parts fabricated from music wire, 52100, 440C, or any other alloy tempered below 375 °F (191 °C). 8.3

Terms used in AMS are clarified in ARP1917.

8.4 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary; dimensions and

properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information.

PREPARED BY “AMEC” AND AMS COMMITTEE “B”

上一页第5页

你可能喜欢

热门文档

相关文档

  • AMS2759-5D中文版

    AMS2759-5D中文版_机械/仪表_工程科技_专业资料。马氏体不锈钢零件的热处理 1. 范围 本规范连同 AMS 2759 中提及的钢的热处理的一般要求一起, 构成了马氏体 ...

  • AMS5703D

    AMS 2759-9D-2009 钢制零件... 5页 5财富值 SAE AMS 5732J-2006 固溶热... 7页 10财富值 AMS H-6875A美国的军用热处... 29页 5财富值 AMS_5630G...

  • AMS2759

    AMS2759_交通运输_工程科技_专业资料。AEROSPACE MATERIAL SPECIFICATION AMS 2759... AMS2759-9D 5页 1下载券 AMS2759-1E 13页 1下载券 AMS2759-8A 13页 1...

  • AMS2759-3E

    AMS2759-3E_机械/仪表_工程科技_专业资料。美国国家标准今日推荐 ... AMS2759-2E AMS2759-5D AMS2759-8A AMS2759-9D AMS2759-9c1/2 相关文档...

  • AMS 2759-9

    AEROSPACE MATERIAL SPECIFICATION AMS 2759/9B Issued Revised NOV 1996 APR 2003... AMS 2759-7A 15页 1下载券 AMS 2759-9D-2009 钢制零... 5页 2下载券 ...

  • AMS2759-1E

    AMS2759-1E_机械/仪表_工程科技_专业资料。美国国家标准今日推荐 ... AMS2759-2E AMS2759-3E AMS2759-5D AMS2759-8A AMS2759-9D AMS2759-9c ...

  • AMS-H-6875A-V2

    环境 气态/燃烧废气 氩 3/ 氦 3/ 氢 3/ 氮 ...本文档零部件的任何参照被 AMS 2759 的相应要求取代...B 和 D 钢制热处理材料的硬度检测:最终热处理后的...

  • AMS2759-8A

    AMS2759-9D 5页 1下载券 AMS2759-5D 11页 1下载券 AMS2759-9c 5页 1下载券 AMS2759-5D中文版 8页 2下载券 AMS2759-3E 15页 1下载券 喜欢此文档的...

  • AMS2759-11

    AMS2759-11_机械/仪表_工程科技_专业资料。美国国家标准今日推荐 ... AMS2759-9D 5页 1下载券 AMS2759_2F 暂无评价 13页 1下载券 AMS2759-5D...

  • AMS 2759宇航材料规范

    2 AMS 2759/3C 3.3.1 果热处 ℉(774 热处理环境: 零件必须在空气中或保护气氛中热处理, 可接受的保护气氛包括氩、 氦、氢中性盐和真空。氮和氮氢混和物...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email