2Type 2205 Code Plus Two® Duplex Stainless Steel
quenching. This treatment applies for both fullsolution annealing and stress-relief annealing.
Machining
2205 may be machined with high-speed steel tooling at the same speeds and feeds as Type 316Laustenitic stainless steel. With carbide tooling, positive rake angle, and C-5 and C-6 grades forroughing and finishing, respectively, should beused. Cutting speeds should be reduced by about20% from those typical for Type 316L. The highstrength of 2205 requires powerful machines andexceptionally strong and rigid tool mounting.
Welding–General Guidelines
The goal in welding any duplex stainless steel is toobtain fusion and heat-affected zones having theexcellent corrosion resistance of the base metal and sufficiently high impact toughness for theapplication. 2205 Code Plus Two®base metalhas an annealed structure with ferrite content inthe range of 30–55%, and is virtually free of
intermetallic phases. Welding procedures should bedesigned to produce this same structure in the weldmetal and heat-affected zones. The weld thermalcycle, as well as filler metal and protection
atmosphere, will control this structure. Near thefusion temperature, the structure of duplex stainlesssteels is entirely ferrite. The desired 30–55% ferritecan be achieved only if the cooling rate is slowenough to allow austenite to re-form as the weldcools. If the cooling rate is too slow, however,embrittling intermetallic phases may form in spiteof the presence of the optimum ferrite content.Extremely low heat input followed by rapid coolingwill produce a predominantly ferritic heat-affectedzone with reduced toughness and corrosion
resistance. This might occur with a GTAW washpass or resistance spot welding. On the other hand,excessive time in the 1300–1800°F (705–980°C)range can lead to formation of intermetallic phaseshaving a similar detrimental effect on properties. Outokumpu Stainless 2205 Code Plus Two hasbeen produced to assist the welder. One importantfeature is that 2205 Code Plus Two has 0.14–0.20%nitrogen, compared to the 0.08–0.20% nitrogenpermitted by ASTM and ASME. This higher
nitrogen helps austenite re-form quickly duringcooling so that the weld and heat-affected zoneare more easily converted back to the optimalaustenitic-ferritic balance. In addition, special quality assurance procedures combined with thehigher nitrogen content make 2205 Code Plus Twomore resistant to formation of intermetallic phases.Avesta Welding Products 2205 filler metals, typicallydesignated as 2209, are more highly alloyed withnickel relative to the base metal to assure a fusionzone with austenite-ferrite balance,toughness, andcorrosion resistance similar to those of the basemetal. With Outokumpu Stainless 2205 base metaland filler, the welder has a workable range of operating conditions. By following the guidelinesprovided in properly qualifiedprocedures,the weldercan produce economical constructions with consistent, high-quality welds.
Control of Intermetallic Phases
2205 duplex stainless steel can experience
several precipitation reactions. The intermetalliccompound, sigma phase, can precipitate between1300–1800°F (705–980°C). Carbides can

Figure 1
Time—Temperature Precipitation Diagram
双相不锈钢焊接介绍Duplex SS briefing_生物学_自然科学_专业资料。Briefing ... Good Weldability Uses Conventional Welding Processes Joint Design Role of ...
Welding Duplex Stainless Steel_材料科学_工程科技_专业资料。This Presentation ...2205 600 500 400 300 6Mo+N 316L 904L 200 100 0 Coefficient of ...
(2006)03-0036-03 关键词 : 双相不锈钢 ; 焊接性 ; 焊接技术 中图分类号 :TG457.1 WeldabilityandWeldingTechniqueof2205DuplexStainlessSteelLIWei-wei1,2,...
welding joint of 2205 duplex stainless plates welded by ferrite fraction and impact toughness at - 40 ℃ of the welding joint increase with the increase ...
Welding of 2205 duplex stainless steel and 304 austenitic stainless steel LI Yan, WANG Shao-gang, Qi-hui, Xin-qiang MA WU (College of Material ...
Duplex SS – higher nickel and molybdenum - 2205, 2003, 2404 ? Super ...flux basicity CONTROL OF HYDROGEN CONTENT Degasing of welding consummables......
AK STEEL 2205Duplex012604_机械/仪表_工程科技_专业资料。P R O D U C ...welded with the GTAW, GMAW, plasma, SMAW and submerged-arc welding methods...
15 Key words :Duplex stainless steel Pipe Welding procedure qualification 2205 双相不锈钢是现代双相不锈钢中的一种 , 用 途广泛 ,具有优良的力学性能 、 ...
ss Ste el 316 L and Duplex Stainle ss Ste el 2205 霍更国 ( 河北国华... TIG welding on analysis o n t he stainless steel of large t ubes ...
The Many Families of Duplex SS Super-duplex Alloys in comparison to 2205 ...more difficult welding and fabrication, but achievable; need for proper ...
热门文档