Type 2205 Code Plus Two® Duplex Stainless Steel3
precipitate between 800–1500°F (425–815°C),and “885 (425°C) embrittlement” can occur inthe temperature range of 650–950°F (340–510°C).If 2205 is held for sufficiently long times in any ofthese temperature ranges, precipitation reactions willoccur. The formation of precipitates can embrittle2205, reducing its ambient temperature ductilityand toughness, and can reduce its corrosion
resistance. The rate of the precipitation reactions isdependent on the chemical composition of 2205and other metallurgical factors. Figure 1 shows aTime-Temperature-Precipitation curve for a 2.25inch (57 mm) thick 2205 plate with 0.14% nitrogen.The curve corresponds to an ambient temperatureimpact toughness of 20 ft.-lb. (27J). Time-temperaturecombinations to the right of the curve have lessthan 20 ft.-lb. of toughness.
Low Temperature Impact TestsLow temperature impact testing may be required bythe ASME code (e.g., Section VIII Div. 1 UHA-51),by a customer specification, or a requirement tomeet ASTM A 923 Method B, which calls for asingle impact test at -40ºF (-40ºC). Many factorsmay adversely affect the low temperature impactproperties of welds, e.g., elevated ferrite content,presence of deleterious phases, and elevated oxygencontent. The latter is a factor in welding processesthat use a flux, and is affected by the type of flux.Welds may not meet the minimum requirements ofA 923 Method B, because these acceptance criteriawere established for solution annealed plate, but thatdoes not necessarily mean detrimental intermetallicphases are present. As a general guideline, it ispossible to arrange the welding processes in orderof increasing impact toughness as follows: SMAW-rutile coating; FCAW; SMAW-basic coating; SAW,GMAW, GTAW. Outokumpu Stainless is willing toassist in choosing the proper welding consumablefor the procedure qualifications based ontest temperature.
Pitting Test
The standard pitting test used on 2205 is ASTM A923 Method C. Prior to the creation of A 923, thepitting test was often referred to as “ASTM G 48Practice B modified.” Testing is done in a ferric
chloride solution at a specific temperature, 25ºC forbase material and 22ºC for annealed welds for 24hours. Other temperatures may be set by
customer specifications, sometimes with minorvariations to the test method. The performance ofwelds in this solution may have no correlation tocorrosion performance in other media and is notintended as a fitness for service test in any specificservice environment. As with impact toughness,the welding process can influence corrosionperformance. The welding processes in order ofincreasing corrosion resistance in this solution are:GTAW; GMAW; FCAW and SAW; SMAW-basiccoating; SMAW-rutile coating. The low ranking ofthe GTAW process is explained by a loss of nitrogenfrom the weld pool. To counteract this effect, it ispossible to either add nitrogen to the torch gas oruse an overalloyed filler metal, e.g., Avesta WeldingProducts P100 (25Cr-9.5Ni-3.6Mo-0.22N).
Joint Design
Some joint designs that can be used for 2205 areshown in Joint Designs 1–8. The goal of thedesigns is full penetration with minimal risk ofburn-through. Many other designs are possible.For example, when the material thickness exceeds0.5 inch (12 mm) and it is possible to weld fromboth sides, the joint designs in Joint Designs 3–5can be made symmetrical.
The root bead may be deposited using eitherGTAW (TIG) or SMAW (coated electrodes).If GTAW is used, an inert backing gas should beapplied when tacking. The root side of a rootbead deposited by SMAW should be cleaned after

Square Butt Joint
Joint Design 1
双相不锈钢焊接介绍Duplex SS briefing_生物学_自然科学_专业资料。Briefing ... Good Weldability Uses Conventional Welding Processes Joint Design Role of ...
Welding Duplex Stainless Steel_材料科学_工程科技_专业资料。This Presentation ...2205 600 500 400 300 6Mo+N 316L 904L 200 100 0 Coefficient of ...
(2006)03-0036-03 关键词 : 双相不锈钢 ; 焊接性 ; 焊接技术 中图分类号 :TG457.1 WeldabilityandWeldingTechniqueof2205DuplexStainlessSteelLIWei-wei1,2,...
welding joint of 2205 duplex stainless plates welded by ferrite fraction and impact toughness at - 40 ℃ of the welding joint increase with the increase ...
Welding of 2205 duplex stainless steel and 304 austenitic stainless steel LI Yan, WANG Shao-gang, Qi-hui, Xin-qiang MA WU (College of Material ...
Duplex SS – higher nickel and molybdenum - 2205, 2003, 2404 ? Super ...flux basicity CONTROL OF HYDROGEN CONTENT Degasing of welding consummables......
AK STEEL 2205Duplex012604_机械/仪表_工程科技_专业资料。P R O D U C ...welded with the GTAW, GMAW, plasma, SMAW and submerged-arc welding methods...
15 Key words :Duplex stainless steel Pipe Welding procedure qualification 2205 双相不锈钢是现代双相不锈钢中的一种 , 用 途广泛 ,具有优良的力学性能 、 ...
ss Ste el 316 L and Duplex Stainle ss Ste el 2205 霍更国 ( 河北国华... TIG welding on analysis o n t he stainless steel of large t ubes ...
The Many Families of Duplex SS Super-duplex Alloys in comparison to 2205 ...more difficult welding and fabrication, but achievable; need for proper ...
热门文档