文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 外语学习 > 英语学习 > Analyzing the effectiveness of an intake compensator for a piston mud pump
侵权投诉

Analyzing the effectiveness of an intake compensator for a piston mud pump

所包括吃饭八角枫

Fig. 2. Diagram of a conical compensator. In the delivery line of a mud pump (the line section 1-2 after the compensator), the fluid inertia is two orders of magnitude or more higher than in the compensator because drilling tubes are so long; i.e. k23>> k12 in Eq. (15) and zX is negligible. Therefore, the choice of k23 is not the deciding factor for decreasing pressure pulsations in the delivery line of a mud pump. It is sufficient to choose the proper charge VoP0 in order to keep 63 within standards. For a pump intake line where the pipe length is short and the coefficient k12 differs by roughly an order of magnitude from k23, it is necessary both to increase k23 and to choose the proper corresponding compensator charge. It can be seen from Eq. (11) that k23 can be increased by increasing the cross-sectional area of the fluid column to the gas cavity in the compensator and decreasing its length h23. In this case the compensator operates best when it is almost completely filled with gas (h23 is minimal). This can be done by finding the compensator volume from Eq. (13) and if the average pressure in Eq. (13) is close to the minimum (p~). However, when the intake head and the feed rate of the pump are decreased, the pressure losses in the intake line drop as the drilling depth increases, which increases the pressure at point 2 and decreases the gas volume in the compensator. Then h23 can be found from Eq. (12); after we substitute it into Eq. (11), we obta

in

2j4 k23=

19'2 P V0P0 --~3 LP3

1/

(16)

We see from Eq. (16) that the cross sectional area of the fluid column in the compensator is what has the greatest effect on k23. Additional parameters must be specified in order to determine this area. For example, if the pump operates with a zero retake head (h= 0), the non-compensation of the inertial pressure is 2x= 0.05. Then, under more severe working conditions, when h> 0, pressure losses from inertia will certainly be less. Therefore k is possible to determine k23 from the parameters of the pump intake line: 1 k23= k22t.S - l ), (17)

and also to calculate the average pressure when the line operates with h= 0. Then the desired conditions will occur for a diameter d23 of the liquid column in the compensator determined from Eqs. (11), (16), and (17): d 2 3>_ 1,11

I a 112(Pl --

pgHVoPod~22 (1 -- A) D g o - - V 12QI2

(18)

) (Pl --~/12 -- QE22)

Equation (18) can be applied to both a cylindrical and a conical compensator (Fig. 2) which can be used in the drilling rigs of the Volgograd Drilling Equipment Plant. In this case d23 is the diameter of the large base of the cone, which characterizes the diameter of the diaphragm and the base of a spherical segment of volume Vo. The height of the conical part can be found from the equation 246

Analyzing the effectiveness of an intake compensator for a piston mud pump

上一页第4页

你可能喜欢

热门文档

相关文档

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email