develop an automation technique for line heating [1] and [2]. Such studies have not only included the thermal-elastic–plastic behavior of the line heating process but also the automation of the process. The first attempt to simulate line heating was performed based on a simplified model [3] and [4]. Throughout the 1990s, many researchers investigated FEM to calculate the residual deformation generated by line heating [2] and [5]. Over the past 9 years, a number of practical systems [6], [7] and [8] have been carried out for the automation of line heating processes. Tango et al. [6] developed an integrated system that carries out line heating automatically. The system, called IHI-Alpha, calculates a heating plan which includes the speed and electric current of induction heating. Park et al. [9] proposed a geometric assessment method in order to establish a theoretical foundation for the automation of line-heating. They focused on measurement, comparison, and the measurement data process in the overall system which was developed for the Samsung Heavy Industry Co., Ltd.
Despite a powerful simulation technique of flame bending, basic studies are still being conducted on the line heating process since the mechanism for line heating is too complicated to obtain accurate control. There is an urgent need for the development of the automation of the forming of curved surfaces.
Compared with flame bending, cold forming can reduce the production time even though it requires significant hydraulic power to form a thick plate. It is well known that die forming is useful for the mass-production of products such as automobiles or consumer goods. However, the fixed die is not suitable for shipbuilding because each hull piece differs. Also, there is no control in the forging process because of the thickness of the hull plates (generally over 12 mm). On the other hand, with the advantage of die-less forming, re-configurable press forming, and multi-point forming, cold forming is an attractive process in many shipyards. The forming system using reconfigurable press technology is a flexible tooling system for the automatic fabrication of arbitrary 3D surface parts [10]. In addition to the inherent flexibility of plate thicknesses, cold forming can form a variety of intricate shell shapes in shipbuilding within a short period of time. Therefore, cold forming technology has been considered in several shipyards as a way to overcome the difficulties associated with traditional line heating [11]. Since 2006, STX Offshore & Shipbuilding Co., Ltd. (STX shipyard) has been investigating cold forming methods that are adequate for shipbuilding. Evaluating the cold bending methods, i.e. multi-press, multi-point dieless forming, and multi-point press forming, the STX shipyard has designed a multi-point press forming (MPPF) device that has a reconfigurable discrete die to form thick plates that have large dimensions. The MPPF is a single-sided reconfigurable-die device with 9 inner rods and 16 edge constraint rods. Inner pressing rods are reconfigured by hydraulic movement in combination with pressing rods in edge constraints. The three-dimensional pressing value for the workpiece should be converted to NC data and downloaded to the machine controller of hydraulic presses that have freedom of movement along the X–Y plane on the guide lines. Through an investigation of the maximum height of the hull pieces extracted from design data of containers, the maximum height of strokes of the punches was designed for manufacturing plates of any size. The in-plane movement of the plates is allowed because the projected area of the plate after the forming process on the initial plane of the plate is smaller than the initial area of the plate before processing. The schematic configuration of the MPPF equipment is illustrated in Fig. 1. The aim of the present study is to provide the MPPF equipment developed by the STX shipyard with a method to calculate the strokes of each pressing punch.
Process design for multi... 暂无评价 6页 2.00元 Method of closed loop... Springback adjustment fo... 暂无评价 13页 免费 Enhancement of Increment.....
Multicore Bundle Adjustment-Manual_计算机软件及应用_IT/计算机_专业资料。三维计算机视觉匹配相关资料Multicore Bundle Adjustment Manual Changchang Wu University of...
Multi--scale Approach for CFRP Composite Simulation by JSTAMP-NV and DIGIMAT_材料科学_工程科技_专业资料。Multi-scale Approach for CFRP Composite Simulation...
for sheet metal part, multi-point forming (MPF) technology is discussed in...3.1 Element group design and shape adjusting mode Height adjustment for ...
216-219. ON MULTI-IMAGE RECONSTRUCTION FROM HISTORIC PHOTOGRAPHS I. ...Multi-image Adjustment of Historic Images of Unknown Orientation with the ...
However, there are no analytical models for variation analysis in multi-station compliant assembly systems. It is critical to develop realistic models for ...
Similar to freeways except inclusion of a few different adjustment factors to determine FFS ? Base conditions for multi-lane highways: – 12’ lanes – ...
Site design plane adjustment work is heavy, if modify the design elevation,...In modern construction engineering, general multi-storey buildings when the ...
热门文档