Springback adjustment for multi-point forming
of thick plates in shipbuilding
Se Yun Hwang, Jang Hyun Lee, Yong Sik Yang, Mi Ji Yoo
Department of Naval Architecture and Ocean Engineering, Inha University, Inchon, 402-751, Republic of Korea Received 27 February 2009. Accepted 19 January 2010. Available online 25 January 2010.
Abstract
At most shipyards, flame bending has been widely used to fabricate curved shells. Since residual deformation of flame bending is produced by thermo-elastic–plastic strains, it is difficult to accurately achieve the desired shape. Therefore, mechanical bending processes such as multi-press forming and multi-point press forming have become attractive because such processes can accurately control the desired shape. Springback is one of the major problems associated with mechanical bending. When the pressing tools are removed after the loading stage, the workpiece springs back due to the elastic recovery and the shape deviation needs to be compensated. The tools of the press forming process therefore need to be changed in order for the produced surface to reach the desired shape accurately after springback. Generally, forming tools are designed and constructed to operate through an iterative process in which the die and the pistons are adjusted to compensate for springback after a pressing operation. Such adjustments require significant time and effort. Therefore, the present study investigates not only how to simulate springback deformation, but also the degree of adjustment required to the stroke of pistons in multi-press forming. Finite Element Analysis (FEA) of thick metal forming and an iterative displacement adjustment algorithm are integrated for practical application. Shape deviations between the design surface and the deformed plate are minimized to reach the desired shape.
Keywords:
press forming Springback; Finite element analysis; Displacement adjustment; Multi-point
1. Introduction
Generally, the objective of the design of a hull form in a marine vessel is to obtain a hull surface with minimum resistance to meet the required dead weight. The geometry of the hull surface is represented by a complex surface. Thereafter, the hull surface is divided into several hundred surface pieces according to the hull-block assembly and the lines of weld joints. In general, more than 50%–70% of the surface pieces are grouped into the curved surface with a double curvature. In most shipyards, the plates with double curvature are deformed from flat plates by flame bending (or line heating) or sequential roll-press forming and flame bending. However, the flame bending process is mostly dependent on the skill of experienced workers because of its complexity in the thermo-elastic–plastic deformation generated by the moving flame. Heating information such as the location of heating lines, sequence of lines, speeds, and maximum temperature have been determined by workers who have several years of experience. Also, flame bending needs to be carried out for several hours to obtain the desired shape since the heat source moves on many lines. Therefore, over the past 40 years many shipyard engineers and scholars have made numerous studies to
Process design for multi... 暂无评价 6页 2.00元 Method of closed loop... Springback adjustment fo... 暂无评价 13页 免费 Enhancement of Increment.....
Multicore Bundle Adjustment-Manual_计算机软件及应用_IT/计算机_专业资料。三维计算机视觉匹配相关资料Multicore Bundle Adjustment Manual Changchang Wu University of...
Multi--scale Approach for CFRP Composite Simulation by JSTAMP-NV and DIGIMAT_材料科学_工程科技_专业资料。Multi-scale Approach for CFRP Composite Simulation...
for sheet metal part, multi-point forming (MPF) technology is discussed in...3.1 Element group design and shape adjusting mode Height adjustment for ...
216-219. ON MULTI-IMAGE RECONSTRUCTION FROM HISTORIC PHOTOGRAPHS I. ...Multi-image Adjustment of Historic Images of Unknown Orientation with the ...
However, there are no analytical models for variation analysis in multi-station compliant assembly systems. It is critical to develop realistic models for ...
Similar to freeways except inclusion of a few different adjustment factors to determine FFS ? Base conditions for multi-lane highways: – 12’ lanes – ...
Site design plane adjustment work is heavy, if modify the design elevation,...In modern construction engineering, general multi-storey buildings when the ...
热门文档