文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 信息与通信 > icl7135四位半LEDLCD显示IC
侵权投诉

icl7135四位半LEDLCD显示IC

ICL7135C, TLC7135C 4 1/2-DIGIT PRECISION ANALOG-TO-DIGITAL CONVERTERS SLAS074B– DECEMBER 1986– REVISED MAY 1999

PRINCIPLES OF OPERATION BUSY output The BUSY output goes high at the beginning of the signal integrate phase. BUSY remains high until the first clock pulse after zero crossing or at the end of the measurement cycle when an over-range condition occurs. It is possible to use the BUSY terminal to serially transmit the conversion result. Serial transmission can be accomplished by ANDing the BUSY and CLOCK signals and transmitting the ANDed output. The transmitted output consists of 10,001 clock pulses, which occur during the signal integrate phase, and the number of clock pulses that occur during the deintegrate phase. The conversion result can be obtained by subtracting 10,001 from the total number of clock pulses. OVER-RANGE output When an over-range condition occurs, this terminal goes high after the BUSY signal goes low at the end of the measurement cycle. As previously noted, the BUSY signal remains high until the end of the measurement cycle when an over-range condition occurs. The OVER RANGE output goes high at the end of BUSY and goes low at the beginning of the deintegrate phase in the next measurement cycle. UNDER-RANGE output At the end of the BUSY signal, this terminal goes high when the conversion result is less than or equal to 9% (count of 1800) of the full-scale range. The UNDER-RANGE output is brought low at the beginning of the signal integrate phase of the next measurement cycle. POLARITY output The POLARITY output is high for a positive input signal and updates at the beginning of each deintegrate phase. The polarity output is valid for all inputs including± 0 and OVER RANGE signals. digit-drive (D1, D2, D4 and D5) outputs Each digit-drive output (D1 through D5) sequentially goes high for 200 clock pulses. This sequential process is continuous unless an over-range occurs. When an over-range occurs, all of the digit-drive outputs are blanked from the end of the strobe sequence until the beginning of the deintegrate phase (when the sequential digit-drive activation begins again). The blanking activity during an over-range condition can cause the display to flash and indicate the over-range condition. BCD outputs The BCD bits (B1, B2, B4 and B8) for a given digit are sequentially activated on these outputs. Simultaneously, the appropriate digit-drive line for the given digit is activated.

system aspects integrating resistor The value of the integrating resistor (RINT) is determined by the full-scale input voltage and the output current of the integrating amplifier. The integrating amplifier can supply 20µA of current with negligible nonlinearity. The equation for determining the value of this resistor is: R INT

+ Full Scale Voltage I INT

Integrating amplifier current, IINT, from 5 to 40

µA yields good results. However, the nominal and recommended current is 20µA.

8

POST OFFICE BOX 655303

DALLAS, TEXAS 75265

icl7135四位半LEDLCD显示IC

上一页第8页

你可能喜欢

  • 数字电压表
  • ICL7135
  • ICL7107
  • 工程电路
  • 温度变送器
  • 中文资料
  • ISD4004

热门文档

相关文档

  • 智能型ICL7135四位半表头程序

    //ICL7135 STROBE signal sbit OVR = P1^4;//ICL7135 Over Range signal sbit UNR = P1^5;//ICL7135 Under Range signal sbit LED = P1^6;//LEDs ...

  • 四位半数字电压表(长大2014)

    模拟条图大致分成三类:①液晶(LCD)条图,呈断续的...本系统所设计的四位半数字电压表由 ICL7135(4 1/...共阳极 LED 发光数 码管、 基准电源、 时钟及量程...

  • 四位半数字电压表课程设计

    共阳极 LED 发光数码管 、基准电源 、时钟及量程...模拟条图大致分成三类:①液晶(LCD)条图,呈断续的...ICL7135 为全 MOS 工艺四位半双积分式 A/D 转换...

  • 四位半的数字万用表

    ICL7135 和单片机芯片 AT89S52 设计 四位半数字万...LED 点阵显示器件可以显示数字,英文字 符,中文字符...LCD 显示 结束 20 数字万用表设计 三、项目准备 ...

  • 四位半数字电压表(长大版)

    使用 LCD1601 液晶模块显示,并可以与 PC 机进行...ICL7135 为全 MOS 工艺 4 位半双积分式 A/D ...通过与 LED 显示值相比较, 其最大偏差即为线性...

  • 四位半数字电压表课程设计内页(长大完美版)

    使用 LCD1601 液晶模块显示,并可以与 PC 机进行...ICL7135 为全 MOS 工艺 4 位半双积分式 A/D ...通过与 LED 显示值相比较, 其最大偏差即为线性...

  • 集成门电路

    ICL7106 3位ADC/驱动LCD ICL7107 3位半ADC/驱动LED ICL7109 4位半ADC/驱动LED ICL7129 4位半ADC/LCD驱动 ICL7135 ADC/LCD驱动BCD输出 ICL7136 3位半CMOS...

  • 4位半数字电压表设计

    使用 LCD1601 液晶模块 显示,并可以与 PC 机进行...通过与LED显示值相比较,其最大偏差即为线性误差。 ...[11] http://www.ic-on-line.com/ ICL7135....

  • 运用单片机制作四位半数字电压表

    用ICL7135CPL制作高精度... 5页 免费 四位半...LCD 显示电路设计 10 3.信号调理总体设计电路图 10...采用 8 位 LED 动态扫描显示的优点是 能改善外部...

  • 四位半数字电压表课程设计论文

    四位半数字电压表【摘要】本文介绍一种数字电压测量电路,该电路采用 ICL7135 ...(4)检查超量程溢出功能,调节输入电压值,当超出测量范围时观察 LED 数 码管...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email