文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 信息与通信 > icl7135四位半LEDLCD显示IC
侵权投诉

icl7135四位半LEDLCD显示IC

ICL7135C, TLC7135C 4 1/2-DIGIT PRECISION ANALOG-TO-DIGITAL CONVERTERS SLAS074B– DECEMBER 1986– REVISED MAY 1999

PRINCIPLES OF OPERATION description of analog circuits input signal range The common mode range of the input amplifier extends from 1 V above the negative supply to 1 V below the positive supply. Within this range, the common-mode rejection ratio (CMRR) is typically 86 dB. Both differential and common-mode voltages cause the in

tegrator output to swing. Therefore, care must be exercised to ensure that the integrator output does not become saturated. analog common Analog common (ANLG COMMON) is connected to the internal IN– during the auto-zero, deintegrate, and zero integrator phases. When IN– is connected to a voltage that is different from analog common during the signal integrate phase, the resulting common-mode voltage is rejected by the amplifier. However, in most applications, IN– is set at a known fixed voltage (i.e., power supply common for instance). In this application, analog common should be tied to the same point, thus removing the common-mode voltage from the converter. Removing the common-mode voltage in this manner slightly increases conversion accuracy. reference The reference voltage is positive with respect to analog common. The accuracy of the conversion result is dependent upon the quality of the reference. Therefore, to obtain a high accuracy conversion, a high quality reference should be used.

description of digital circuits RUN/HOLD input When RUN/HOLD is high or open, the device continuously performs measurement cycles every 40,002 clock pulses. When this input is taken low, the integrated circuit continues to perform the ongoing measurement cycle and then hold the conversion reading for as long as the terminal is held low. When the terminal is held low after completion of a measurement cycle, a short positive pulse (greater than 300 ns) initiates a new measurement cycle. When this positive pulse occurs before the completion of a measurement cycle, it will not be recognized. The first STROBE pulse, which occurs 101 counts after the end of a measurement cycle, is an indication of the completion of a measurement cycle. Thus, the positive pulse could be used to trigger the start of a new measurement after the first STROBE pulse. STROBE input Negative going pulses from this input transfer the BCD conversion data to external latches, UARTs, or microprocessors. At the end of the measurement cycle, STROBE goes high and remains high for 201 counts. The most significant digit (MSD) BCD bits are placed on the BCD terminals. After the first 101 counts, halfway through the duration of output D1– D5 going high, the STROBE terminal goes low for 1/2 clock pulse width. The placement of the STROBE pulse at the midpoint of the D5 high pulse allows the information to be latched into an external device on either a low-level or an edge. Such placement of the STROBE pulse also ensures that the BCD bits for the second MSD are not yet competing for the BCD lines and latching of the correct bits is ensured. The above process is repeated for the second MSD and the D4 output. Similarly, the process is repeated through the least significant digit (LSD). Subsequently, inputs D5 through D1 and the BCD lines continue scanning without the inclusion of STROBE pulses. This subsequent continuous scanning causes the conversion results to be continuously displayed. Such

subsequent scanning does not occur when an over-range condition occurs.

POST OFFICE BOX 655303

DALLAS, TEXAS 75265

icl7135四位半LEDLCD显示IC

上一页第7页

你可能喜欢

  • 数字电压表
  • ICL7135
  • ICL7107
  • 工程电路
  • 温度变送器
  • 中文资料
  • ISD4004

热门文档

相关文档

  • 智能型ICL7135四位半表头程序

    //ICL7135 STROBE signal sbit OVR = P1^4;//ICL7135 Over Range signal sbit UNR = P1^5;//ICL7135 Under Range signal sbit LED = P1^6;//LEDs ...

  • 四位半数字电压表(长大2014)

    模拟条图大致分成三类:①液晶(LCD)条图,呈断续的...本系统所设计的四位半数字电压表由 ICL7135(4 1/...共阳极 LED 发光数 码管、 基准电源、 时钟及量程...

  • 四位半数字电压表课程设计

    共阳极 LED 发光数码管 、基准电源 、时钟及量程...模拟条图大致分成三类:①液晶(LCD)条图,呈断续的...ICL7135 为全 MOS 工艺四位半双积分式 A/D 转换...

  • 四位半的数字万用表

    ICL7135 和单片机芯片 AT89S52 设计 四位半数字万...LED 点阵显示器件可以显示数字,英文字 符,中文字符...LCD 显示 结束 20 数字万用表设计 三、项目准备 ...

  • 四位半数字电压表(长大版)

    使用 LCD1601 液晶模块显示,并可以与 PC 机进行...ICL7135 为全 MOS 工艺 4 位半双积分式 A/D ...通过与 LED 显示值相比较, 其最大偏差即为线性...

  • 四位半数字电压表课程设计内页(长大完美版)

    使用 LCD1601 液晶模块显示,并可以与 PC 机进行...ICL7135 为全 MOS 工艺 4 位半双积分式 A/D ...通过与 LED 显示值相比较, 其最大偏差即为线性...

  • 集成门电路

    ICL7106 3位ADC/驱动LCD ICL7107 3位半ADC/驱动LED ICL7109 4位半ADC/驱动LED ICL7129 4位半ADC/LCD驱动 ICL7135 ADC/LCD驱动BCD输出 ICL7136 3位半CMOS...

  • 4位半数字电压表设计

    使用 LCD1601 液晶模块 显示,并可以与 PC 机进行...通过与LED显示值相比较,其最大偏差即为线性误差。 ...[11] http://www.ic-on-line.com/ ICL7135....

  • 运用单片机制作四位半数字电压表

    用ICL7135CPL制作高精度... 5页 免费 四位半...LCD 显示电路设计 10 3.信号调理总体设计电路图 10...采用 8 位 LED 动态扫描显示的优点是 能改善外部...

  • 四位半数字电压表课程设计论文

    四位半数字电压表【摘要】本文介绍一种数字电压测量电路,该电路采用 ICL7135 ...(4)检查超量程溢出功能,调节输入电压值,当超出测量范围时观察 LED 数 码管...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email