文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 信息与通信 > icl7135四位半LEDLCD显示IC
侵权投诉

icl7135四位半LEDLCD显示IC

ICL7135C, TLC7135C 4 1/2-DIGIT PRECISION ANALOG-TO-DIGITAL CONVERTERS SLAS074B– DECEMBER 1986– REVISED MAY 1999

PRINCIPLES OF OPERATION integrating capacitor The product of the integrating resistor and capacitor should be selected to give the maximum voltage swing without causing the integrating amplifier output to saturate and get too close to the power supply voltages. When the amplifier output is within 0.3 V of either supply, saturation occurs. With± 5-V supplies and ANLG COMMON connected to ground, the designer should design for a± 3.5-V to± 4-V integrating amplifier swing. A nominal capacitor value is 0.47µF. The equation for determining the value of the integrating capacitor (CINT) is: C INT Clock I INT+ 10, 000 Output Period Swing Integrator Voltage

Where: IINT is nominally 20µA. Capacitors with large tolerances and high dielectric absorption can induce conversion inaccuracies. A capacitor that is too small could cause the integrating amplifier to saturate. High dielectric absorption causes the effective capacitor value to be different during the signal integrate and deintegrate phases. Polypropylene capacitors have very low dielectric absorption. Polystyrene and polycarbonate capacitors have higher dielectric absorption, but also work well. auto-zero and reference capacitor Large capacitors tend to reduce noise in the system. Dielectric absorption is unimportant except during power up or overload recovery. Typical values are 1µF. reference voltage For high-accuracy absolute measurements, a high quality reference should be used. rollover resistor and diode The ICL7135C and TLC7135C have a small rollover error; however, it can be corrected. The correction is to connect the cathode of any silicon diode to INT OUT and the anode to a resistor. The other end of the resistor is connected to ANLG COMMON or ground. For the recommended operating conditions, the resistor value is 100 k . This value may be changed to correct any rollover error that has not been corrected. In many noncritical applications the resistor and diode are not needed. maximum clock frequency For most dual-slope A/D converters, the maximum conversion rate is limited by the frequency response of the comparator. In this circuit, the comparator follows the integrator ramp with a 3-µs delay. Therefore, with a 160-kHz clock frequency (6-µs period), half of the first reference integrate clock period is lost in delay. Hence, the meter reading changes from 0 to 1 with a 50-µV input, 1 to 2 with a 150-µV input, 2 to 3 with a 250-µV input, etc. This transition at midpoint is desirable; however, when the clock frequency is increased appreciably above 160 kHz, the instrument flashes 1 on noise peaks even when the input is shorted. The above transition points assume a 2-V input range is equivalent to 20,000 clock cycles. When t

he input signal is always of one polarity, comparator delay need not be a limitation. Clock rates of 1 MHz are possible since nonlinearity and noise do not increase substantially with frequency. For a fixed clock frequency, the extra count or counts caused by comparator delay are a constant and can be subtracted out digitally. For signals with both polarities, the clock frequency can be extended above 160 kHz without error by using a low value resistor in series with the integrating capacitor. This resistor causes the integrator to jump slightly towards the zero-crossing level at the beginning of the deintegrate phase, and thus compensates for the comparator delay. This series resistor should be 10 to 50 . This approach allows clock frequencies up to 480 kHz.

POST OFFICE BOX 655303

DALLAS, TEXAS 75265

icl7135四位半LEDLCD显示IC

上一页第9页

你可能喜欢

  • 数字电压表
  • ICL7135
  • ICL7107
  • 工程电路
  • 温度变送器
  • 中文资料
  • ISD4004

热门文档

相关文档

  • 智能型ICL7135四位半表头程序

    //ICL7135 STROBE signal sbit OVR = P1^4;//ICL7135 Over Range signal sbit UNR = P1^5;//ICL7135 Under Range signal sbit LED = P1^6;//LEDs ...

  • 四位半数字电压表(长大2014)

    模拟条图大致分成三类:①液晶(LCD)条图,呈断续的...本系统所设计的四位半数字电压表由 ICL7135(4 1/...共阳极 LED 发光数 码管、 基准电源、 时钟及量程...

  • 四位半数字电压表课程设计

    共阳极 LED 发光数码管 、基准电源 、时钟及量程...模拟条图大致分成三类:①液晶(LCD)条图,呈断续的...ICL7135 为全 MOS 工艺四位半双积分式 A/D 转换...

  • 四位半的数字万用表

    ICL7135 和单片机芯片 AT89S52 设计 四位半数字万...LED 点阵显示器件可以显示数字,英文字 符,中文字符...LCD 显示 结束 20 数字万用表设计 三、项目准备 ...

  • 四位半数字电压表(长大版)

    使用 LCD1601 液晶模块显示,并可以与 PC 机进行...ICL7135 为全 MOS 工艺 4 位半双积分式 A/D ...通过与 LED 显示值相比较, 其最大偏差即为线性...

  • 四位半数字电压表课程设计内页(长大完美版)

    使用 LCD1601 液晶模块显示,并可以与 PC 机进行...ICL7135 为全 MOS 工艺 4 位半双积分式 A/D ...通过与 LED 显示值相比较, 其最大偏差即为线性...

  • 集成门电路

    ICL7106 3位ADC/驱动LCD ICL7107 3位半ADC/驱动LED ICL7109 4位半ADC/驱动LED ICL7129 4位半ADC/LCD驱动 ICL7135 ADC/LCD驱动BCD输出 ICL7136 3位半CMOS...

  • 4位半数字电压表设计

    使用 LCD1601 液晶模块 显示,并可以与 PC 机进行...通过与LED显示值相比较,其最大偏差即为线性误差。 ...[11] http://www.ic-on-line.com/ ICL7135....

  • 运用单片机制作四位半数字电压表

    用ICL7135CPL制作高精度... 5页 免费 四位半...LCD 显示电路设计 10 3.信号调理总体设计电路图 10...采用 8 位 LED 动态扫描显示的优点是 能改善外部...

  • 四位半数字电压表课程设计论文

    四位半数字电压表【摘要】本文介绍一种数字电压测量电路,该电路采用 ICL7135 ...(4)检查超量程溢出功能,调节输入电压值,当超出测量范围时观察 LED 数 码管...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email