ICL7135C, TLC7135C 4 1/2-DIGIT PRECISION ANALOG-TO-DIGITAL CONVERTERS SLAS074B– DECEMBER 1986– REVISED MAY 1999
timing diagrams (continued) STROBE AUTO ZERO Digit Scan for OVER RANGE D5 Signal Integrate Deintegrate
D4
D3
D2
D1 First D5 of AUTO ZERO and deintegrate is one count longer.
Figure 4
PRINCIPLES OF OPERATION A measurement cycle for the ICL7135C and TLC7135C consists of the following four phases. 1. Auto-Zero Phase. The internal IN+ and IN– inputs are disconnected from the terminals and internally connected to ANLG COMMON. The reference capacitor is charged to the reference voltage. The system is configured in a closed loop and the auto-zero capacitor is charged to compensate for offset voltages in the buffer amplifier, integrator, and comparator. The auto-zero accuracy is limited only by the system noise, and the overall offset, as referred to the input, is less than 10µV. 2. Signal Integrate Phase. The auto-zero loop is opened and the internal IN+ and IN– inputs are connected to the external terminals. The differential voltage between these inputs is integrated for a fixed period of time. When the input signal has no return with respect to the converter power supply, IN– can be tied to ANLG COMMON to establish the correct common-mode voltage. Upon completion of this phase, the polarity of the input signal is recorded. 3. Deintegrate Phase. The reference is used to perform the deintegrate task. The internal IN– is internally connected to ANLG COMMON and IN+ is connected across the previously charged reference capacitor. The recorded polarity of the input signal ensures that the capacitor is connected with the correct polarity so that the integrator output polarity returns to zero. The time required for the output to return to zero is proportional to the amplitude of the input signal. The return time is displayed as a digital reading and is determined by the equation 10,000× (VID/Vref). The maximum or full-scale conversion occurs when VID is two times Vref. 4. Zero Integrator Phase. The internal IN– is connected to ANLG COMMON. The system is configured in a closed loop to cause the integrator output to return to zero. Typically, this phase requires 100 to 200 clock pulses. However, after an over-range conversion, 6200 pulses are required.
6
POST OFFICE BOX 655303
DALLAS, TEXAS 75265

//ICL7135 STROBE signal sbit OVR = P1^4;//ICL7135 Over Range signal sbit UNR = P1^5;//ICL7135 Under Range signal sbit LED = P1^6;//LEDs ...
模拟条图大致分成三类:①液晶(LCD)条图,呈断续的...本系统所设计的四位半数字电压表由 ICL7135(4 1/...共阳极 LED 发光数 码管、 基准电源、 时钟及量程...
共阳极 LED 发光数码管 、基准电源 、时钟及量程...模拟条图大致分成三类:①液晶(LCD)条图,呈断续的...ICL7135 为全 MOS 工艺四位半双积分式 A/D 转换...
ICL7135 和单片机芯片 AT89S52 设计 四位半数字万...LED 点阵显示器件可以显示数字,英文字 符,中文字符...LCD 显示 结束 20 数字万用表设计 三、项目准备 ...
使用 LCD1601 液晶模块显示,并可以与 PC 机进行...ICL7135 为全 MOS 工艺 4 位半双积分式 A/D ...通过与 LED 显示值相比较, 其最大偏差即为线性...
使用 LCD1601 液晶模块显示,并可以与 PC 机进行...ICL7135 为全 MOS 工艺 4 位半双积分式 A/D ...通过与 LED 显示值相比较, 其最大偏差即为线性...
ICL7106 3位ADC/驱动LCD ICL7107 3位半ADC/驱动LED ICL7109 4位半ADC/驱动LED ICL7129 4位半ADC/LCD驱动 ICL7135 ADC/LCD驱动BCD输出 ICL7136 3位半CMOS...
使用 LCD1601 液晶模块 显示,并可以与 PC 机进行...通过与LED显示值相比较,其最大偏差即为线性误差。 ...[11] http://www.ic-on-line.com/ ICL7135....
用ICL7135CPL制作高精度... 5页 免费 四位半...LCD 显示电路设计 10 3.信号调理总体设计电路图 10...采用 8 位 LED 动态扫描显示的优点是 能改善外部...
四位半数字电压表【摘要】本文介绍一种数字电压测量电路,该电路采用 ICL7135 ...(4)检查超量程溢出功能,调节输入电压值,当超出测量范围时观察 LED 数 码管...
热门文档