等角挤压
2022 Shu-yong JIANG, et al/Trans. Nonferrous Met. Soc. China 23(2013) 2021 2028
grain size of 100 nm via ECAE, and found that ECAE results in the occurrence of (011) compound twins in addition to 011 II type and {11 I type twins in the martensitic microstructures at room temperature, and leads to a considerable improvement in the thermal stability of phase transformation temperatures and thermal hysteresis as well as an increase in the critical stress level for dislocation slip due to grain size refinement. ECAE of NiTi SMA at high temperatures such as 1123 K and 1023 K has been investigated and the grain refinement is insufficient and dynamic recovery occurs rather than dynamic recrystallization during ECAE at high temperatures [15,16]. The two-step phase transformations in the ECAE-processed NiTi sample such as B2→R→B19' upon cooling and B19'→R→B2 upon heating have been reported [17,18].
So far, how to manufacture the ultrafine-grained NiTi SMA tube has never been reported in the literatures. In the present study, ECAE of NiTi SMA tube is preliminarily investigated by means of the process experiments, finite element method (FEM) and microscopy.
2 Experimental
2.1 Fundamentals of ECAE
The schematic diagram of ECAE of NiTi SMA tube is shown in Fig. 1. The NiTi SMA tube in which the steel core is placed is inserted into the steel can and is sealed by means of the NiTi plug. According to the fundamentals of ECAE of the bulk metal material, the steel can with the NiTi SMA tube in it is placed into the ECAE die and then is imparted to SPD which leads to the grain refinement of the NiTi SMA tube. In the study, the cross-section of the steel can is selected as the square. The channel angle is determined as 120°.
2.2 Experimental materials
The NiTi SMA tube sample for ECAE is shown in




Fig. 2. The NiTi SMA tube, which possesses the inner diameter of 3 mm, the wall thickness of 0.5 mm and the height of 15 mm, was fabricated from the NiTi SMA bar with the diameter of 12 mm by means of electro- discharge machining (EDM). The NiTi SMA bar with a nominal composition of Ni50.9Ti49.1 (mole fraction, %) was prepared by vacuum induction melting method before it was rolled at 800 °C, and finally was drawn to the NiTi bar at 400 °C. As a sealed part, the NiTi plug with the diameter of 4 mm and the height of 5 mm was also fabricated from the NiTi SMA bar. The steel can and the steel core were made of low carbon steel. The steel can had a square cross-section of 6 mm×6 mm and a height of 25 mm. Furthermore, there was a blind hole with the inner diameter of 4 mm and the height of 20 mm in the steel can. The steel core possessed the diameter of 3 mm and the height of 15 mm. The lubricant was coated between the steel core and the NiTi SMA tube as well as between the steel can and the NiTi tube in order to make it easy to remove the NiTi SMA tube after ECAE. The original microstructure of the NiTi SMA tube before ECAE is shown in Fig. 3, where the original microstructure of the NiTi SMA tube belongs to the equiaxed grains.







Fig. 1 Schematic diagram of ECAE of NiTi SMA tube
Fig. 2 Schematic diagram of NiTi SMA tube samples for ECAE: (a) Unassembled parts; (b) Assembled sample (section)
在等通道转角挤压过程中 ,镍钛 形状 记忆 合金管内部装 有钢 芯,然后将其封装在钢套中 。基于 刚粘塑 性有 限元法 ,镍钛形状记忆合 金管等通 道转 角...
4251. [12] [2] [13] [3] [14] [4] [15] [5] [16] [6] [17] [7] [18] [8] 镍钛形状记忆合金管的等通道转角挤压江树勇 1,赵亚楠 1,张...
CuZnAl形状记忆合金等通道转角挤压工艺的研究 研究了Cu-25.04Zn-3.83Al-0.2Zr形状记忆合金的ECAP过程以及不同温度挤压后组织和性能的变化。结果表明:在200℃...
等通道转角挤压FeMnSiCrNiC形状记忆合金时效过程中碳化物析出的研究_专业资料。研究了等通道转角挤压后时效处理对FeMnSiCrNiC合金碳化物的析出和形状记忆效应的影响。结果...
退火温度对等通道转角挤压态铁基形状记忆合金力学性能的影响 研究了退火温度对等通道转角挤压(ECAP)Fe17.80Mn4.73Si7.80Cr4.12Ni合金力学性能及显微组织的影响。...
退火温度对等通道转角挤压态铁基形状记忆合金力学性能的影响张 伟 ,李宁 ,文玉华... 相变热滞大和价格 便宜等特点 ,在一次性连接紧固元件 ,特别是管接头中 有着...
TB2钛合金等通道转角挤压变形过程的应变分析及实验研究_专业资料。运用有限元方法对TB2钛合金等温等通道转角挤压过程进行有限元模拟及实验研究。模拟结果表明,材料变形...
Ti-6Al-4V钛合金等通道转角挤压有限元模拟_专业资料。对Ti-6Al-4V钛合金的等通道转角挤压过程进行三维有限元模拟,分析不同的凸模下压速度对等通道转角挤压过程的...
等通道转角挤压(ECAP)工艺的研究现状_材料科学_工程科技_专业资料。维普资讯 ... 镍、 铁等 多种 合金 中获得 了超 细 晶粒组 织 ¨ .被证实是 一种 ...
热门文档