等角挤压
Shu-yong JIANG, et al/Trans. Nonferrous Met. Soc. China 23(2013) 2021 2028
2023




Fig. 3 Optical microstructure of original NiTi SMA tube
2.3 ECAE process
The assembled NiTi SMA tube samples were placed into the ECAE die and then they were put into the Instron 5500R universal testing machine, where the assembled SMA NiTi tube samples were heated to 500 °C. Subsequently, the pressing punch moved down at the speed of 1 mm/s. Consequently, the assembled SMA
NiTi tube samples were forced to go across the channel
of the die and thus the ECAE process was finished.
2.4 Compression test
The NiTi SMA samples with the diameter of 4 mm and the height of 6 mm were prepared from the NiTi SMA bar whose state was identical to the NiTi SMA tube for ECAE and were used for compression test in order to obtain the constitutive model of the NiTi SMA. In the same manner, the steel samples with the diameter of 4 mm and the height of 6 mm were prepared from the low carbon steel used for the steel can and the steel core
for ECAE and were used for compression test in order to
Fig. 4 Stress—strain curves of NiTi SMA at 500 °C obtain the involved constitutive model. The compression
experiments were carried out on the Instron 5500R
3.2 Finite element model universal testing machine at the strain rates ranging from
DEFORM3D finite element code was used to 0.001 s 1 to 1 s 1 and at 500 °C.
simulate ECAE of NiTi shape memory alloy tube. Figure
7 indicates the finite element model of ECAE of NiTi 2.5 Microstructural observation
SMA tube. It can be seen from Fig. 7 that the boundary The microstructures of the compressed NiTi SMA
conditions are very complicated and there exist multiple samples as well as the NiTi SMA tubes before ECAE and
after ECAE were observed by means of optical coupled boundary conditions, such as between NiTi tube
and steel core, between NiTi tube and steel can, between microscopy. All the specimens for optical microscopy
NiTi plug and steel can, between NiTi plug and NiTi tube, were etched in a solution of 10% HF + 40% HNO3 +
between NiTi plug and steel core, between steel core and 50% H2O.
steel can, between steel can and die, between steel can
3 Finite element simulation of ECAE of NiTi and punch and between NiTi plug and punch. According
to the ECAE process parameters, the pressing speed of SMA tube
the punch is selected as 1 mm/s, and the pressing stroke
3.1 Constitutive model of the punch is determined as 20 mm during the finite
Establishing the appropriate constitutive model of element simulation.
NiTi SMA plays a significant role in simulating ECAE
of the NiTi SMA tube. Figure 4 demonstrates the stress—strain curves of NiTi SMA at 500 °C and the strain rates of 0.001, 0.01, 0.1 and 1 s 1, respectively. It can be seen from Fig. 4 that the true stress of NiTi SMA increases with increasing the strain rate, which indicates that NiTi SMA is sensitive to the strain rates and thus belongs to rigid-viscoplastic materials at 500 °C. Figure 5 shows the microstructures of the involved compressed samples at different strain rates, which reveal that NiTi SMA is obviously characterized by dynamic recovery at all the strain rates instead of dynamic recrystallization. Therefore, ECAE of NiTi SMA tube was carried out at 500 °C. The constitutive model of NiTi SMA in Fig. 4 shall be used as the material model in subsequent finite element simulation of ECAE of NiTi SMA tube. The true stress—strain curves of the low carbon steel for the steel can and the steel core at 500 °C are illustrated in Fig. 6 and are used as the material model of the steel can and the steel core during ECAE of NiTi SMA tube. Therefore, multiple constitutive models including NiTi SMA tube, NiTi plug, steel can and steel core are applied during ECAE of NiTi SMA tube.




在等通道转角挤压过程中 ,镍钛 形状 记忆 合金管内部装 有钢 芯,然后将其封装在钢套中 。基于 刚粘塑 性有 限元法 ,镍钛形状记忆合 金管等通 道转 角...
4251. [12] [2] [13] [3] [14] [4] [15] [5] [16] [6] [17] [7] [18] [8] 镍钛形状记忆合金管的等通道转角挤压江树勇 1,赵亚楠 1,张...
CuZnAl形状记忆合金等通道转角挤压工艺的研究 研究了Cu-25.04Zn-3.83Al-0.2Zr形状记忆合金的ECAP过程以及不同温度挤压后组织和性能的变化。结果表明:在200℃...
等通道转角挤压FeMnSiCrNiC形状记忆合金时效过程中碳化物析出的研究_专业资料。研究了等通道转角挤压后时效处理对FeMnSiCrNiC合金碳化物的析出和形状记忆效应的影响。结果...
退火温度对等通道转角挤压态铁基形状记忆合金力学性能的影响 研究了退火温度对等通道转角挤压(ECAP)Fe17.80Mn4.73Si7.80Cr4.12Ni合金力学性能及显微组织的影响。...
退火温度对等通道转角挤压态铁基形状记忆合金力学性能的影响张 伟 ,李宁 ,文玉华... 相变热滞大和价格 便宜等特点 ,在一次性连接紧固元件 ,特别是管接头中 有着...
TB2钛合金等通道转角挤压变形过程的应变分析及实验研究_专业资料。运用有限元方法对TB2钛合金等温等通道转角挤压过程进行有限元模拟及实验研究。模拟结果表明,材料变形...
Ti-6Al-4V钛合金等通道转角挤压有限元模拟_专业资料。对Ti-6Al-4V钛合金的等通道转角挤压过程进行三维有限元模拟,分析不同的凸模下压速度对等通道转角挤压过程的...
等通道转角挤压(ECAP)工艺的研究现状_材料科学_工程科技_专业资料。维普资讯 ... 镍、 铁等 多种 合金 中获得 了超 细 晶粒组 织 ¨ .被证实是 一种 ...
热门文档