文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 机械/仪表 > BS 1768-1963 统一精密六角螺栓、螺钉和螺母(UNC与UNF螺纹)规范
侵权投诉

BS 1768-1963 统一精密六角螺栓、螺钉和螺母(UNC与UNF螺纹)规范

BS 1768-1963 统一精密六角螺栓、螺钉和螺母(UNC与UNF螺纹)规范

BS 1768-1963 统一精密六角螺栓、螺钉和螺母(UNC与UNF螺纹)规范

BS1768:1963

Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSI

The bolt or screw shall be screwed into the grip or nut to the thread run-out of the bolt or screw and then unscrewed six full threads. The bolt or screw shall be subjected to the proof stress for bolts and screws specified in Column 3 of Table 4 in Appendix A by applying the appropriate load as given in Table 5, Appendix A and maintaining for ten seconds and then releasing.

ii) Method of measurement. Measurement of the specimens subjected to the proof stresses for bolts or screws shall be performed in the following manner:

The overall length of the bolt or screw shall be measured at its true centre line with an instrument capable of measuring changes in length of 0.0001 in.

After the bolt or screw has been stressed in accordance with the provisions of i) of this clause, its length shall again be measured. There shall be no permanent elongation of the bolts or screws, but to allow for errors of determination between consecutive measurements of bolt or screw length, this condition is considered to have been achieved if the measurement is within±0.0005 in of that made before loading.

NOTEThe preferred method of carrying out this test is to measure the length between conical centres on the centre line of the bolt or screw which has been set up on the mating centres of the anvils of the measuring fixture; the head or shank of the bolt or screw should be marked so that it can be placed in the same position for all measurements.

6 Grading and mechanical properties of steel nuts

a. Grading. Nuts shall be graded as follows:

GRADE 0. Nuts suitable for use with bolts, GradesA, B and P.

The nuts shall be capable of withstanding a proof load, based on the minimum tensile strength of GradeP Bolts, as laid down in Table 4, Column 2.

GRADE 1. Nuts suitable for use with Bolts Grade S.

These nuts shall be capable of withstanding a proof load, based on the minimum tensile strength of GradeS Bolts, as laid down in Table 4, Column 2.

GRADE 3. Nuts suitable for use with Bolts Grade T.

These nuts shall be capable of withstanding a proof load, based on the minimum tensile strength of GradeT Bolts, as laid down in Table 4, Column 2.

GRADE 5. Nuts suitable for use with Bolts Grades V and X.

These nuts shall be capable of withstanding a proof load, based on the minimum tensile strength of GradeX Bolts, as laid down in Table 4, Column 2.b. Mechanical properties.i) Proof load.Nuts 1 in diameter and under. These nuts shall meet the requirements for proof load specified inTable 6. They shall be tested in accordance with the method described in Clause 7.

Nuts over 1 in diameter. As equipment of sufficient capacity may not be readily available for nuts in this range, they shall meet the requirements for hardness specified in sub-clausec) below.c. Hardness.

i) Nuts over 1 in diameter. Nuts of diameters over1 in shall be subjected to a hardness test and their hardness shall not be less than that specified below:

Brinell Hardness

Grade 0 Nuts–120 HB 10/3000min.Grade 1 Nuts–180 HB 10/3000 min.Grade 3 Nuts–230 HB 10/3000min.© BSI 10-1999

3

上一页第9页

热门文档

相关文档

  • 美制统一螺纹表UNC_UNF

    UN,UNF,UNC,UNEF 英制螺纹区别 英寸制统一螺纹的识别 英寸制统一螺纹,在英寸制国家广泛采用, 该类螺纹分三个系列:粗 牙系列 UNC ,细牙系列 UNF ,特细牙系列...

  • 美制统一螺纹表UNC UNF

    美制统一螺纹表UNC UNF_机械/仪表_工程科技_专业资料。美制粗细螺纹规格美制标准系列统一螺纹的基本公称 基本大经 牙数 直径 D,d(in) n 6 8 10 12 1/4 5...

  • 美制统一螺纹表UNC_UNF

    美制统一螺纹表UNC_UNF_机械/仪表_工程科技_专业资料 暂无评价0人阅读0次下载举报文档 美制统一螺纹表UNC_UNF_机械/仪表_工程科技_专业资料。美制标准系列统一...

  • 美制统一螺纹表UNC_UNF

    美制统一螺纹表UNC_UNF_机械/仪表_工程科技_专业资料 暂无评价0人阅读0次下载举报文档 美制统一螺纹表UNC_UNF_机械/仪表_工程科技_专业资料。美制标准系列统一...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email