文档下载 文档下载导航
设为首页 | 加入收藏
搜索 请输入内容:  
 导航当前位置: 文档下载 > 所有分类 > 工程科技 > 机械/仪表 > BS 1768-1963 统一精密六角螺栓、螺钉和螺母(UNC与UNF螺纹)规范
侵权投诉

BS 1768-1963 统一精密六角螺栓、螺钉和螺母(UNC与UNF螺纹)规范

BS 1768-1963 统一精密六角螺栓、螺钉和螺母(UNC与UNF螺纹)规范

BS 1768-1963 统一精密六角螺栓、螺钉和螺母(UNC与UNF螺纹)规范

BS1768:1963

ii) Nuts up to and including 1 in diameter. For nuts up to and including 1 in diameter, a hardness test is not part of the requirements of this standard but for general guidance Brinell hardness values are given below:

Birnell Hardness

Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSI

Grade 0 Nuts–120/235 HB 10/3000Grade 1 Nuts–163/240 HB 10/3Grade 3 Nuts–183/300 HB 10/3Grade 5 Nuts–270/335 HB 10/3iii) Preparation of specimens.accordance with BS 240 “Method of Bridell hardness test.” If Vickers or Rockwell methods are used, reference should be made to BS 860 “Table of approximate comparison of hardness scales” for appropriate values.

The test shall be made on the end faces of the nuts.

d. Assembly testing of nuts. When nuts up to and including 3/4 in diameter are torque tested to destruction they shall not fail by splitting of the wall.

7 Proof load for nuts

a. Method of test (see Figure 17 in Appendix C). The proof load for nuts shall be determined by assembling the sample nut on a hardened threaded mandrel as specified in sub-clause b) below. A load axial with the mandrel and equal to the proof load for nuts specified in Table 6 shall be applied against the nut. The nut shall satisfactorily resist this load without stripping and should be removable by the fingers after the test. If the threads of the mandrel are damaged during the test the test shall be discarded.

b. Test mandrel. The test mandrel shall have a hardness of not less than 365 HV30. It shall be threaded to Class 3A tolerances in accordance with BS 1580, “Unified screw threads”, except that the major diameter shall be equal to the minimum major diameter as specified in the standard subject to a plus tolerance of0.002 in.

8 Dimensions

The bolts, screws and nuts shall conform to the dimensions and tolerances given in Table 1 to Table 3 inclusive and Clauses 9 to 15 inclusive.

9 Length of bolts and screws

a. The nominal length of a bolt or screw shall be the distance from the underside of the head to the extreme end of the shank including any chamfer or radius.

NOTE

The nominal lengths of bolts and screws normally stocked are given in Appendix D.Nominal length

in

Diameter

in

Tolerance of length

inb. The permissible tolerance on the nominal length shall be as given below:

Up to and including 1Over 1 up to and including 2Over 2 up to and including 6Over 6

Up to and including 3/4Over 3/4

Up to and including 3/4 Over 3/4

Up to and including 3/4Over 3/4

All diameters

+ 0–1/32+ 0–1/16+ 0–1/16+ 0–1/8+ 0–3/32+ 0–3/16+ 0–3/16

4

标准分享网 doc.guandang.net 免费下载

© BSI 10-1999

上一页第10页

热门文档

相关文档

  • 美制统一螺纹表UNC_UNF

    UN,UNF,UNC,UNEF 英制螺纹区别 英寸制统一螺纹的识别 英寸制统一螺纹,在英寸制国家广泛采用, 该类螺纹分三个系列:粗 牙系列 UNC ,细牙系列 UNF ,特细牙系列...

  • 美制统一螺纹表UNC UNF

    美制统一螺纹表UNC UNF_机械/仪表_工程科技_专业资料。美制粗细螺纹规格美制标准系列统一螺纹的基本公称 基本大经 牙数 直径 D,d(in) n 6 8 10 12 1/4 5...

  • 美制统一螺纹表UNC_UNF

    美制统一螺纹表UNC_UNF_机械/仪表_工程科技_专业资料 暂无评价0人阅读0次下载举报文档 美制统一螺纹表UNC_UNF_机械/仪表_工程科技_专业资料。美制标准系列统一...

  • 美制统一螺纹表UNC_UNF

    美制统一螺纹表UNC_UNF_机械/仪表_工程科技_专业资料 暂无评价0人阅读0次下载举报文档 美制统一螺纹表UNC_UNF_机械/仪表_工程科技_专业资料。美制标准系列统一...

站点地图 | 文档上传 | 侵权投诉 | 手机版
本站所有资源均来自互联网,本站只负责收集和整理,均不承担任何法律责任,如有侵权等其它行为请联系我们.
文档下载 Copyright 2013 doc.guandang.net All Rights Reserved.  -  email