BS 1768-1963 统一精密六角螺栓、螺钉和螺母(UNC与UNF螺纹)规范

BS1768:1963
3 Finish
a. General. The bolts, screws and nuts shall be cleanly finished, sound and free from defects.
b. Types of finish. Steel precision bolts, screws and nuts are normally supplied with the following finishes:i) Heat treated bolts and screws. The surfaces of these bolts and screws are customarily dull black from and screws after heat treatment.
ii) Bright finished bolts and screws.machined finish.
iii) Nuts. These may be bright on all surfaces or dull black where heat treated.
iv) Special finishes. If steel bolts, screws or nuts are required bright all over, the purchaser should state this in his enquiry and order.
If the purchaser requires bolts, screws or nuts of steel or other material to be coated, he should state the type of coating required in his enquiry and order.
Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSI
4 Mechanical properties of steel bolts and screws
Steel bolts and screws shall meet the requirements for mechanical properties specified in Table 4 of Appendix A.
NOTE
For guidance concerning the comparison of strength grades of BS 1768 and BS 970-1:1983 see Table 4A.
a. Tensile strength and proof stress. The tensile strength and the proof stress shall be determined by the methods of test described in Clause 5.
b. Minimum elongation. Test specimens for the measurement of elongation shall be machined from the shank of the bolt to the dimensions for standard round test specimens as given in BS 18 “Tensiletesting of metals” and shall be concentric with the axis of the bolt. They shall be tested in accordance with the standard procedure as given in BS 18.
NOTEThe minimum elongation values in Table 4 are based on a gauge length of 4ÆArea; BS18 now specifies a gauge length of5.65ÆArea, but values appropriate to this length are not yet available for the higher grades of steel. The former gauge length and its associated values have therefore been retained in this standard for the time being and a suitable amendment will be issued when the necessary information can be supplied.
c. Minimum Izod impact value. Test specimens for Izod impact test shall be machined from the bolt to the dimensions specified for standard test pieces in BS131-1, “The Izod impact test on metals” and shall be tested in accordance with the standard procedure as given in BS 131-1.
Where an Izod test is not practicable, a nicked fracture test may be substituted.d. Hardness.
i) General. A hardness test on bolts and screws is not part of the requirements of this standard, but Brinell hardness values are given for guidance in Table 4 of Appendix A.
ii) Method of test. The Brinell hardness test is carried out in accordance with the method specified in BS240 “Method of Brinell hardness test” Part1 and is made on the top of the head or on the point of the bolt or screw.
5 Tensile strength and proof stress of bolts and screws
a. Tensile strength. The tensile test on a bolt or screw shall be carried out as follows:
An ordinary nut or its equivalent in the form of an adaptor shall be screwed on to the bolt or screw so as to be clear of the run-out of the thread towards the head and also clear of any imperfect threads at the point, the load shall then be applied to the head and to the nut or adaptor.b. Proof stress. The proof stress for bolts shall be determined as follows:
i) Method of test. The proof stress for bolts or screws shall be determined with a straight full size
threaded bolt or screw. The bolt or screw shall be placed in a suitable testing machine with the threaded end of the bolt or screw in a threaded grip or in a nut. The grips of the testing machine shall be self-aligning to avoid side thrust (see Figure 16 in Appendix C).
2
标准分享网 doc.guandang.net 免费下载
© BSI 10-1999
UN,UNF,UNC,UNEF 英制螺纹区别 英寸制统一螺纹的识别 英寸制统一螺纹,在英寸制国家广泛采用, 该类螺纹分三个系列:粗 牙系列 UNC ,细牙系列 UNF ,特细牙系列...
美制统一螺纹表UNC UNF_机械/仪表_工程科技_专业资料。美制粗细螺纹规格美制标准系列统一螺纹的基本公称 基本大经 牙数 直径 D,d(in) n 6 8 10 12 1/4 5...
美制统一螺纹表UNC_UNF_机械/仪表_工程科技_专业资料 暂无评价0人阅读0次下载举报文档 美制统一螺纹表UNC_UNF_机械/仪表_工程科技_专业资料。美制标准系列统一...
美制统一螺纹表UNC_UNF_机械/仪表_工程科技_专业资料 暂无评价0人阅读0次下载举报文档 美制统一螺纹表UNC_UNF_机械/仪表_工程科技_专业资料。美制标准系列统一...
热门文档