BS 1768-1963 统一精密六角螺栓、螺钉和螺母(UNC与UNF螺纹)规范

BS1768:1963
1 Scope
This British Standard covers the Normal series of Unified precision hexagon bolts, screws and nuts having Unified screw threads in a range of nominal sizes from 1/4 in to 2 in inclusive. The dimensional
requirements of this standard apply both to ferrous and non-ferrous bolts, screws and nuts. Mechanical properties are given only in respect of steel bolts, screws and nuts, and the finishes in which they are normally supplied are described in Clause 3.
NOTEIt is considered that the range of nominal sizes included in this standard is adequate for most of the applications for which this series is likely to be employed, but for the convenience of users requiring larger sizes, the formulae from which the proportions for bolt heads and nuts are derived are given in Appendix F.
Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSI
2 Material and manufacture
a. General. In order to provide for the different methods of manufacture by which bolts, screws and nuts to this standard may be produced, a choice of materials is given.
Bolts, screws and nuts in sizes up to and including3/4 in nominal size are most commonly produced by cold forging from wire; larger sizes are generally produced by hot forging. Bolts, screws and nuts can also be produced by machining from hexagon bars.
Bolts and screws produced by cold forging shall, except in the case of bolts and screws bright finished to Grade A (see Table 4, Appendix A) be heat-treated after forging.
Bolts, screws and nuts produced by hot forging or by turning from bars, and cold formed nuts shall beheat-treated when this is necessary to give the requisite mechanical properties specified inClauses4 and 6 and Appendix A.
b. Cold forged bolts and screws. The choice of material used to manufacture bolts and screws by cold forging shall normally be at the discretion of the manufacturer. The finished products shall comply with the requirements for physical properties as set out in Clause 4 and in Table 4 of Appendix A.
If, however, the purchaser wishes to specify the composition of the material to be used, this shall be the subject of agreement with the manufacturer.
c. Cold forged nuts and hot forged bolts, screws and nuts. The material to be used for cold forged nuts or hot forged bolts, screws and nuts depends to a large extent on the size of the product. Unless otherwise
stipulated by the purchaser, the choice of material shall therefore be left to the manufacturer provided that the finished products satisfy the requirements for mechanical properties set out in Clauses 4 and 6 and in Table 4 and Table 6 of Appendix A, but recommendations on suitable materials are given for guidance in Table 8 and Table 10 of Appendix B.
d. Bolts, screws and nuts machined from bars. Table 9and Table 10 of Appendix B give a selection of steels from BS970 which are among those suitable for particular grades of bolts, screws and nuts. Unless
otherwise stipulated by the purchaser, the choice of material shall be left to the manufacturer provided that the finished products satisfy the requirements for mechanical properties set out in Clauses 4 and 6 and in Table 4 and Table 6 of Appendix A.
e. Decarburization. As normally manufactured from wire of ordinary quality, a proportion of threads
produced on forged bolts and screws by rolling may have some surface decarburization (principally at crests of threads). For highly stressed bolt applications, the definition and degree of such decarburization shall be negotiated between manufacturer and user. For bolts of strength GradeT and greater, the depth of decarburization, measured from the crest, shall not exceed 33per cent of the height of the threads.
Complete freedom from any decarburization is achieved by shank grinding after heat treatment and before thread rolling; if this is required, it shall be the subject of negotiation between manufacturer and user.f. Rolling laps. When threads are produced by rolling, small laps are commonly present at the crests and are generally of a magnitude which is not detrimental to the performance of the bolt.
per cent of the depth of the thread.
© BSI 10-1999
1
UN,UNF,UNC,UNEF 英制螺纹区别 英寸制统一螺纹的识别 英寸制统一螺纹,在英寸制国家广泛采用, 该类螺纹分三个系列:粗 牙系列 UNC ,细牙系列 UNF ,特细牙系列...
美制统一螺纹表UNC UNF_机械/仪表_工程科技_专业资料。美制粗细螺纹规格美制标准系列统一螺纹的基本公称 基本大经 牙数 直径 D,d(in) n 6 8 10 12 1/4 5...
美制统一螺纹表UNC_UNF_机械/仪表_工程科技_专业资料 暂无评价0人阅读0次下载举报文档 美制统一螺纹表UNC_UNF_机械/仪表_工程科技_专业资料。美制标准系列统一...
美制统一螺纹表UNC_UNF_机械/仪表_工程科技_专业资料 暂无评价0人阅读0次下载举报文档 美制统一螺纹表UNC_UNF_机械/仪表_工程科技_专业资料。美制标准系列统一...
热门文档