无损检测工艺规程(超 声 波 检 验)-双语版
NJBST Co.,Ltd.
QCD-013
Rev.:0
Page:8 of 12 7.3.1.2 用斜射波对焊缝横向反射 体作扫查. 斜射波反射方向基本上与焊缝 方 向平行.要适当操作探头,以使超 声能量能通过 ASME 规范有关卷 规定的焊缝和邻近母材金属的体 积.扫查中,应将增益调整到比基 准灵敏度高一倍.应参照灵敏度基 准作出评定,应将探头转过 1800, 并重新检验. 7.4 直探头 应对邻近的母材金属进行直射 波扫查,以探测有可能影响斜射波 检验结果辨认的反射体,但此不作 为验收—拒收的检验.应对这些反 射体的位置和区域作出记录. 7.5 当规范有要求时,应在可能达 到的范围内用直探头对焊缝和母 材金属进行扫查.扫查中,应将增 益调整到至少比基准灵敏度高一 倍.应参照灵敏度基准作出评定. 8. 评定 8.1 用 DAC 检验 用 DAC 曲线时,凡信号超过 20%DAC 的任何反射体均应对其 定形,定性,定位 ,并按本规程 第 9 条给出的验收标准作出评定. 9. 验收判废标准 凡信号超过参考基准 20%的缺陷均 应定形,定性,定位,并按以下验 收标准评定: (a) 定为裂纹,未熔合或未焊透的 缺陷,无论长短,均不合格: (b) 若信号超过参考基准波幅,且 其长度超过下值的其他缺陷均不 合格. 其中 t 为不包括许可余高的焊缝 厚度.若对接焊缝连接处壁厚不 同,t 取两种厚度较薄者.若全焊 透焊缝
包括一填角焊缝,则填角 腰高应包括在 t 中. 10. 记录和报告 10.1 检验记录 超声校准记录中应包括仪器校准 记录.还应包括超声检验系统校准 和校准试块编号. 10.2 检验记录 每种超声检验应标出和记录下列 内容:
Title: ULTRASONIC EXAMINATION PROCEDURE 7.4 Straight Beam The scanning of the adjacent base metal shall be performed to detect reflectors that might affect interpretation of angle beam results, and is not to be used as acceptance-rejection examination. Locations and areas of such reflectors shall be recorded. 7.5 The weld and base metal shall be scanned, where required by the referencing Code Section to the extent possible with the straight beam search unit. The scanning shall be performed at a gain setting of at least two times the primary reference level. 8. EVALUATION 8.1 Examination Using DAC For examination using a distance amplitude correction curve (DAC), any reflector which causes an indication in excess of 20% of DAC shall be investigated to the extent that it can be evaluated in terms of the acceptance rejection standards given in 9 of this procedure. 9. ACCEPTANCE-REJECTION STANDARDS All imperfections that produce an indication greater than 20% of the reference level shall be investigated to the extent that the operator can determine the shape, identity, and location of all such imperfections and evaluate them in terms of the acceptance standards given in (a) and (b) below. (a) Imperfections characterized as cracks, lack of fusion, or incomplete penetration are unacceptable regardless of length. (b) Other imperfections are unacceptable if the indications exceed the reference level amplitude and have the lengths which exceed : Thickness 壁厚 t in. mm <3/4 <19 3/4~9/4 >9/4 19~57 >57 Ultrasonic Indicated Length 超声指示长度 in mm 1/4 6 1/3t 3/4 19
Where t is the thickness of the weld excluding any allowable reinforcement. For a butt weld having different thicknesses at the weld, t is the thinner of these two thicknesses. If a full penetration weld includes a fillet weld, the thickness of the throat of the fillet shall be included in t. 10. RECORDS AND REPORTS
10.1 Calibration Records Instrument calibrations shall be included in the ultrasonic calibration records. Ultrasonic examination system calibration requirements and calibration block identity shall be included in the ultrasonic calibration records. 10.2 Examination Records For each ultrasonic examination, the following information shall be identified and recorded:

超声波检测工艺规程_机械/仪表_工程科技_专业资料...承压设备无损检测 GB50235-1997 工业金属管道工程... 在达到所检工件最大声程时,其灵敏度余量应≥10...
无损检测工艺规程1_机械/仪表_工程科技_专业资料...无 损 检 测 工 艺 规 程 ZW09-04-08 总份...标准 11 条标准 11.3 附录C 超 声 波 探 伤 ...
无损探伤工艺及超声波应用_信息与通信_工程科技_...无损检测工艺规程无损检测工艺规程是按本单位的受检...焊缝的超声波检测———可用直射声束法或斜射声束法...
单斜探头、双晶探头等,在达到所检 工件的最大检测声程时,其有效灵敏度余量≥... 超声波探伤工艺规程 9页 免费 无损检测工艺规程(液体渗... 9页 免费 无损...
超声波探伤操 作工艺规程 1. 主题内容与适用范围 ...2 引用标准 JB4730-2005《 承压设备无损检测》 JB...a 仪器和探头的组合灵敏度:在达到所检工件最大声...
本规程规定了无损检测人员应具备的资格,本公司所采用的四种无损检测方法射线检 测、超声检测、磁粉检测和渗透检测,检测设备,检测工艺,检测时机,验收标准及档案的 ...
探伤工艺规范 超声波探伤工艺规范 磁粉探伤工艺规范 ...d. 探头主声束应无双峰、无偏斜。 2.2.2 采用...是被检焊缝的厚度,两厚度不等的焊接件,T 则是两...
超声波检测工艺规程_机械/仪表_工程科技_专业资料...3 引用标准 JB4730《压力容器无损检测》 GB150《... 在达到所检工件最大声程时,其灵敏度余量应≥10...
无损检测工艺规程_六年级其它课程_其它课程_小学...1.6 校准 校准在基准试块上进行,使超声波主声束...2.8.8 复验 当决定复验时,必须对被检面进行...
超声无损检测通用...超声波检测通用工艺规程编制: 编制: 审核: 审核: ...按表2选择和使用 DAC 曲线灵敏度,按表3进行验 收...
热门文档